Question about 1987 Honda Accord

1 Answer

Brakes bled brakes,master full of brake fluid,brake pedal still goes to floor,also noise comes from back end

Posted by on

  • jlpatrizi May 11, 2010

    What kind of noise? is there drums in rear? did you adjust them?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,779 Answers

What was done to the car as far as brakes recently? Is the master cylinder leaking? If not, u have air in the lines. Bleed wheel greatest distance from master cyl., working your way to the closest wheel last. Keep checking the master cyl. level, cause if it gets too low, u will have to start over again. When do u hear the noise from the back? When u apply the brakes? Have u pulled the rear drums to look and see what's going on? Let me know the answers to the above, and bleed the brakes in the order described. Let me know what s going on,.

Posted on Jan 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 Jeep Grand Cherokee brake pedal goes all the way to the floor. Recently replaced calipers and master cylinder and bled the whole system. Brake pedal goes all the way to the floor when first pushed...


Not bleed properly
or you have a rusted out line (leak)

There is NO Procedure-- that when driving a
vehicle or bleeding brakes,do you ever pump them

Dec 03, 2014 | 1994 Jeep Grand Cherokee

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

1 Answer

No brake pedal. pads good, fluid up in master. pedal won,t come up when bled?


fluid is by passing rubbers in master cylinder . replace unit. noise if you are running engine could be air leaking from faulty booster unit

Feb 01, 2013 | Cars & Trucks

2 Answers

Front and rear drum brakes, the pads are ok, but the brake pedal started going to the floor. When I tried to bleed them, the rear bleeder screws broke. So I replaced both wheel cylinders. The rubber...


OK........as you have stated that you have bled the brakes properly.....was there fluid coming out each bleed nipple as a flowing stream...????

And did you shut off the bleed nipple half way down stroke....?????

If this is all ok, then I would be looking at a failed master cylinder.......and what is occurring is the fluid is leaking from the primary to the secondary within the master cylinder !!!!!

Mar 31, 2011 | Ford Mustang Cars & Trucks

3 Answers

Replace brakes. now they go to the floor. bled air


When you fixed the brakes, did you take the lid off the master cylinder. I just wonder if you spilled out your brake fluid. The only reason the pedal should go to the floor is if the brake fluid is gone or the master cylinder is not working. Check the fuse. Check the brake fluid level. The pedal only goes to the floor if there is no back pressure in the lines between the master cylinder the lines to the brake pistion on the calipers. Please give me a good ratin and keep me informed.

Jul 07, 2009 | 1999 Cadillac DeVille

2 Answers

1989 Ford F350 2 wheel drive dually 460 ci gas motor


5 Inspect Brake Fluid Type Brake fluid loss or contamination grey_line.gif 10 Inspect Master Cylinder (Brake System) Worn or leaking brake master cylinder. grey_line.gif 11 Inspect Brake Power Booster Damaged booster vacuum line/check valve, or diaphram

Nov 24, 2008 | 1989 Ford F 350

Not finding what you are looking for?
Cars & Trucks Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...