Question about 1999 Plymouth Grand Voyager

1 Answer

Blower motor i have 99 plymouth grand voyager and the blower is out how do i change it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

It's in behind glove box, you will probably have to remove glove box, but a good look up from under will tell you. You did check fuses & resistor right? Did it run for a while on high only?

Posted on Feb 08, 2009

  • 1 more comment 
  • Robert White Mountain Nov 21, 2011

    i have a 99 ply grand voyager and the heater started to slow down and when we hit the dash or under the glove box, it would come backon for a while then finally nothing...is it motor, resistor or both

  • Robert White Mountain Nov 21, 2011

    it would ruun if i hit the glove box or under the glove box and finally didnt work at all

  • Mike Butler
    Mike Butler Nov 23, 2011

    Pretty simple to bench test motor once you have it out, plus feel for rough/loose/worn bearings on shaft of motor as well, then you'll know for sure. Personally, I would spend the extra while under there and replace resistor while your at it. Then your done.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change waterpump on a 99 plymoth grand voyager 3.3 motor


i need your help about problem water pump. I did exchanged new water pump. but it keep increase hot up .. i still figure something out about water pump. do you think fan cooling broke either fuse blow out .. thank you ..

Jan 17, 2010 | 1998 Plymouth Grand Voyager

1 Answer

'99 Plymouth Grand Voyager fan switch issues


The problem is not with the switch, it's the blower motor resistor. The resistor is usually located in duct work near the blower motor. It will have 4or 5 wires going to it and is held in place with a couple screws. These things generate heat, so they put them in duct work so the fan blows air across them to keep them cool. Sometimes the plug gets hot and melts, you should be able to buy the resitor and the plug with wires (pig tail) from an auto parts store or a dealer. The resistors are usually about $50 the pig tail is about $30.

Dec 02, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Replace blower motor 1998 plymouth voyager


it is located behind and below the glove box,you might want to remove the glove box assembly to see it easier,
there are four screws holding a blower motor cover you to take off first,now remove the screws holding the blower motor up,disconnect the motor wires.
if your changing this because you think its bad,you should test the blower motor wires with a test light with the key on and blower switch turned on.if you have power in the wires,then it is bad.
but if you have no power in wires it could be blower motor resister,or switch.

Nov 28, 2009 | 1998 Plymouth Voyager

1 Answer

I have a 2000 Plymouth Grand Voyager. The control for the blower motor only works in the last position. I got a new controller and plugged it in and tried it but that didn't fix the problem. Any ideas?


This really sounds like you have a blower motor resistor that has failed. The blower motor resistor is located almost right next to the physical blower motor itself mounted on the eveporator case...(same case the blower motor bolts onto).When these fail it only allows on side of the resistor to let current pass through the pigtail to to motor....hence being stuck on one speed...be it low or high...get back to me if you have any more questions... HOPE I COULD HELP!!!

Nov 20, 2009 | 2000 Plymouth Grand Voyager

1 Answer

The fan blower only works on high. The other


its the resistor, and its located with the blower motor. you will need a new motor assy. .......in Chryslers infinite wisdom, its all one unit.

Oct 08, 2009 | 1998 Plymouth Voyager

1 Answer

Replacing Blower fan info


Should be only 3 screws holding it in Unplug, remove the screws and remove the blower motor.

May 29, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Blower selector switch problem


if there is swich problem
if there is wire problem
if there is loos wire
if all ok check power suplly

Mar 21, 2009 | 1999 Plymouth Voyager

1 Answer

Location needed for blower senser on 99 plymouth voyager


the blower resistor is under the hood at the firewall on pass side... there are no screws just tabs holding it in place... the pigtail is usually needed when the resistor goes bad it melts the harness

Feb 12, 2009 | 1999 Plymouth Grand Voyager

2 Answers

Automatic belt tensionor


Same tensioner or a new one?

Jun 16, 2008 | 1999 Plymouth Grand Voyager

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...