Question about 1999 Dodge Durango

1 Answer

Where is the crank sensor located?

Where is the crank sensor located on the 99 Dodge Durango 5.9 V8, and is it easy to fix?

Posted by on

  • Burple May 01, 2009

    How do you take the wheelhouse liner off without breaking the tabs?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 137 Answers

The sensor is bolted to the top of the cylinder block near the rear of right cylinder head
The sensor is accessed by removing the right front fender liner

  1. Remove right front tire and right front wheelhouse liner.
  2. Disconnect crankshaft position sensor pigtail harness from main wiring harness.
  3. Remove two sensor (recessed hex head) mounting bolts
  4. Remove sensor from engine.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Will a bad pick up coil stop a 1999 dodge Durango from cranking


It wouldn't stop the engine from turning over while trying to start. But it can make engine not start or run poorly

Sep 12, 2015 | Dodge Cars & Trucks

2 Answers

99 Dodge Durango 5.9l V8 turning over but not starting. Strong smell of gas from air intake. Plugs sound like sparking. Fluids good and clean air filter. Any ideas?


Cam Sensor Failure Causing no Start or Stalling : Dodge ...

repairpal.com > Problems > Dodge > Durango
Dodge Durango Cam Sensor Failure Causing no Start or Stalling. ... On the 4.7L V8engine, the Camshaft position sensor failure can cause the engine to crank but not start or it can ... On the 5.9L V8 engine, rerouting the ignition coil wire and spark plug wires can help solv. ... 1999 Dodge Durango ... Drove good till put gas.

Aug 05, 2015 | Dodge Cars & Trucks

1 Answer

Where is the crankshaft sensor on my '99 durango 5.2 4x4?


Hi Sheila, I'm glad to help. The crank sensor is located on top of the transmission bell housing very difficult to get to. Hope this helps and have an awesome day Sheila.

May 05, 2014 | 1999 Dodge Durango

1 Answer

1998 darango runs good then dies has fuel pressure no spark


I personally own a 99 Durango and have run into this myself. It would be going along just peachy and then it would stall like you turned the key off. Sound familiar? It is a common issue with the 5.2 and 5.9. All it is, is a bad crank sensor. Its located on the drivers rear side of the engine at the 2:00 position. Replace it and all should be well.

If i have helped you please rate me. Cheers!

Dec 12, 2011 | 1998 Dodge Durango

1 Answer

Have a 99 dodge durango 5.9 v8. seems to have a fuel filter stopped up. need to know where to locate filter and difficulty in changing.


is either along the frame or in the frame. if it's on the frame, easy to change, if its in the frame, i recommend you take it to a mechanic

Aug 21, 2011 | Dodge Durango Cars & Trucks

1 Answer

2001 dodge durango v8 5.9 trans won't shift unless i downshift


I have a 2000, there is a speed sensor located in top of the rear axel and I believe another on the tranny housing. Try the rear axel first.

Jun 01, 2009 | 2001 Dodge Durango

4 Answers

I have a 2000 dodge durango, I have a code P0320.


I put in a new crank positioning sensor and it fixed my problem. 42.00 dollars from NAPA. took about 2 hours to change it.

Mar 09, 2009 | 2000 Dodge Durango

1 Answer

WHERE IS THE CRANK SHAFT SENOR?


The crank sensor is located on the trans. bell housing.Look behind the engine where the tranny bolts to the block and on top of the bell housing just a little off center you will see the sensor which has 2 bolts mounting it in place.It has a 6in length of wire attached to it with a plug on the end.This sensor reads off the flywheel.Hope this helps.

Mar 03, 2009 | 1999 Dodge Durango

4 Answers

Crank sensor location 1999 dodge durango


the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.

Feb 22, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

1,100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...