Question about 1995 Nissan Pathfinder

2 Answers

95 pathfinder only 1 headlight comes on both bulbs good

High beam indicator stays on when lights switched on, doesn't matter if high or low beam is selected.
only right headlight iluminates when switch is turned on.
only 5 v at left lamp harness, right light has 12v
have tried new switch but thats not the problem.
tested 12v at the right and left headlight fuses

Posted by on

  • 4 more comments 
  • baloota Jan 08, 2009

    no

    3 wires come into the harness, but they all go into a mass of wrapped wires. is there anywhere specific to check the ground?

  • baloota Jan 08, 2009

    sorry had a brain fart

    checked the continuity of the ground into the left side wire plug appears to be good.

  • jcb4696 Jan 29, 2009

    headlights go off when i hit a bump, I believe it is a loose ground. How do I check to see the ground connection?

  • airbrusher May 06, 2009

    I am totally NOT a mechanic and I have the same problem, so could you tell me where exactly the daytime running light module is located? Thanks, in advance.

  • dwkcool May 11, 2010

    have you checked the ground in the left side wire plug

  • Anonymous Mar 18, 2014

    2006 Cayanne turbo s v8

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Im a mechanic who owns a1995 pathfinder, had the same problem.your trouble is in your daytime running light module. try giving it a tap, bet they will come back on

Posted on Feb 07, 2009

  • Adam Wiederspohn
    Adam Wiederspohn Oct 29, 2011

    hi i have 9 5 pathfinder both day time running lights come on both brights turn on bot only one dim come on what would cuose that

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

You have two spades straight up and down and one side to side that is the ground

Posted on Jan 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left operating headlight not working


the switch supplies power to the relays that switch on the lights according to the position you have it at
so on high beam there will be 2 high beam lights working
on low beam there will be 2 low beam lights working
back to passing lights or flashing head lights , both beams will work so the switch is the last item to consider
Now with only one side beam not working it comes back to the ground on that light for that bulb
remember that electricity follows the path of least resistance so it the ground is bad the current will ground out through another point including a light which will switch that light off or make it not work
remember the brakes light that flask when an indicator is used --same thing

Jan 24, 2016 | 2000 Nissan Maxima

1 Answer

Why don't lights work?


Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
Low and High Beams Headlamps Inoperative ?
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Did you check the headlamp relay ? Location ,left instrument panel
Did

Nov 11, 2015 | 2001 Chevrolet Monte Carlo

2 Answers

How do I fix HI beam headlights?


your switch is not good try to double check your switch.

Mar 09, 2015 | Kia Spectra Cars & Trucks

2 Answers

My headlights wont work


I don't believe there is a fuse. There is a circuit breaker built into the headlight switch. If you are sure the headlight switch is good, it could be a bad dimmer switch. If you have a voltmeter, with the headlight switch turned on, a larger yellow wire going from the headlight switch to the dimmer switch should be a hot wire. The dimmer switch sends power on a tan wire to the low beams, and through a light green wire to the high beam bulbs.
If your high beam indicator on the dash also doesn't work, then it is likely one of those switches. A voltmeter or test light would need to be used to find which one is bad. If you can find the connector at the steering column going to the dimmer switch, pull it apart and check for power on the yellow wire coming from the headlight switch, with the headlight switch turned on. If no power, the headlight switch is bad. If there is power there, then the dimmer switch must be bad.

Jan 21, 2014 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Headlights wont turn


sounds like the headlight switch is defective and needs replacing,but you need to check to make sure the rod that the switch pushes against if make the full travel and not short as this will not allow the switch to change from low beam to high beam.if the rod is travelling the full length then the switch is no good.you should also hear a click when moving the arm to go from low to high if not then the switch is bad.by holding the lever at a certain position to get the high beams to work this also indicates a switch problem.

Nov 04, 2013 | Cars & Trucks

1 Answer

2006 Hyundai Tycson GL Headlight Problems


Could be a defective headlight relay, Located in the fuse block in engine compartment,

Nov 29, 2012 | Cars & Trucks

1 Answer

High beam indicator comes on with fog lights


Could your Mazda have daytime running lights? If you checked all fuses, did that include the three in the joint box?

There is an auto light-off control module that is central to all functions you describe. It is assumed that you would only turn on the fog lights with headlights on and set for high beam. If you set the headlight switch to LOW, the module closes the headlight relay to turn on the low beams. If you then turn the headlight switch to HIGH, the module turns on the high beams and allows you to turn on the FOG LIGHT switch, closing the fog light relay and turning on the fog lights. Since this sequence is not working, I suggest checking both high beam lamps as both could be burned out. Other possibilities are a defective headlight switch or the module

Oct 01, 2012 | 2005 Mazda 6

1 Answer

My daytime running lights work, high beams will come on but switch wont stay on, have to hold it. Low beams do not work and daytime running light dash indicator stays on all the time. Is it a relay or...


if you have to hold the switch so the high beams stay on then that indicates a bad/worn switch,you could have 2 problems the day time running light relay may have a problem with it.i would first replace the headlight switch at the base of the steering colume as by the info you supply its not changing to the high beam side without holding the switch in position.

May 25, 2011 | 1998 Pontiac Sunfire

Not finding what you are looking for?
1995 Nissan Pathfinder Logo

942 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...