Question about 1984 Chevrolet Corvette

1 Answer

Upon heavey acceration car falls on face

Upon decellaration car moves somewaht normal

Posted by on

  • hallkaren Jan 08, 2009

    110,000 miles

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

I would have to say that you have a fuel pump going out or a clogged up fuel filter how many miles do you have on the car

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pushed key into doorlock cylinder fell inside door. How do I fix this problem?


New car!
LOL oops sorry
there is a clip inside door that holds cylinder from falling out, but cylinder face is normally a little wider than hole in door and keeps it from falling in.
i am guessing either cylinder face exterior worn narrower,
or hole in door got wider. it may depend on type of car.
JB weld may fill the gap if you keep it off the inside turning mechanism.
you will need to get inside door panel off to do this which most yank out of plastic snap in grommets, some may have screws somewhere maybe on inside door handle, etc.
good luck, (if not worried about looks, i'd thicken the hole with duc tape, one of my favs)

Feb 23, 2015 | Cars & Trucks

1 Answer

2005 Dodge Stratus 2.4L,runs good until you start to drive it, then it bogs down and falls on its face


could be clogged fuel filter or low fuel pressure due to a weak pump or fuel pressure regulator.

Sep 05, 2012 | 2005 Dodge Stratus

1 Answer

Started engine, normal idle, but when you try to accerate the engine falls flat...either in or out of gear. replaced fuel filter and checked TPS. Continuity is per specs, but voltaqge is backwards...5 v...


First thing I'd do is check the fuel pressure w/ the engine running and then see if it holds the pressure w/ the engine off. If not, then the fuel pump is probably faulty.

Aug 04, 2012 | 1993 Subaru Legacy

1 Answer

Motor clicks upon hard acceration


it most likely is a spark knock ( ping ) try using high test fuel if the ping goes away try cleaning or replace the EGR valve . ( exhust gas recerulating valve ).

Dec 12, 2011 | 1996 Mercury Grand Marquis

1 Answer

1991 Cutlas Calias with 110,000 miles on it. When it gets up to high rpm's it falls on its face. Sometimes it will stall. If you drive slow its ok. When you put it to the floor and heads up to high...


is your car still running on carburetor engine? if yes, have your carburetor cleaned. while cleaning, replace the secondary jet in your carb. the normal primary/secondary jet for a 1.6cc engine is 105/135.

Aug 05, 2011 | 1991 Oldsmobile Cutlass Calais

1 Answer

Just replaced plugs, changed oil and filter, upon excelleration, she falls on her face (has no power to GO) What's wrong with her?


Did you replace fuel filter? I'd start there and run a good fuel system cleaner through it (STP, Gumout, etc) You also might consider having an OBII scan done (fault scan) any good parts store (Autozone, Advance, etc) can do that FREE - scan will show any faults your cars' computer has tracked.

Mar 06, 2011 | 1993 Buick Park Avenue

1 Answer

Pedals don't fully move when pressing the Adjustable Pedal button


sounds like the brake/accelertor adjuster motor isnt working... 1st start by checkin the fuses under the dash if all looks well go down to where the accerator pedal/motor is and check for 12v at the connector if your gettin 12v with the switch depressed replace the accerator pedal adjuster motor

Jun 02, 2010 | 2003 Lincoln Town Car

1 Answer

1999 Blazer 4.3 TBI Fuel Meter Body


Hello;
The injectors on a TBI unit do not float. They should not move at all. There are three or four screws that mount the injectors to the throttle body as well as the fuel inlet and return lines. Sounds as if either the screws backed out or are missing. They are a T-25 Torx.
Make sure the screws are all in and tight. Good luck and rate me highly.
Thanks;
Rich
RPM Northwest

Apr 29, 2009 | 1999 Chevrolet Blazer

1 Answer

How do i remove the transmission off a 1991 isuzu pickup?


put truck on jack stands disconect batt . remove driveshaft/ starter .torqconverter bolts if automatic. if standerd slave cyl .shifter linkage .when all ***** are out of your way remove crossmember under trans . if 6 cyl dont let distributor hit firewall remove bellhousing bolts trans should fall out ..... support trans with jack .....dont get under trans it is heavey!!!!!!!!!!!!!!

Mar 05, 2009 | 1991 Isuzu Pickup

1 Answer

Saturn running poorly


its probly your catlaitc converter is cloged

Jan 20, 2009 | 1993 Saturn SC1

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...