Question about Mitsubishi Eclipse

1 Answer

Upgrade Camshafts Is is possible to apply performance 272 camshafts on a non-turbo 4g63 without changing the pistons?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 52 Answers

Yes it is but anytime you change to a bigger camshaft you should always check for clearance.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need camshaft torque specs ?


Are you doing all this work without a shop manual? It should have the info you seek.

Jul 16, 2015 | 1998 Acura Integra

1 Answer

Code p0019 p0018 p0008


P0019: Cam/Crankshaft Pos. Correlation Sensor B - Bank 2
P0018: Cam/Crankshaft Pos. Correlation Sensor A - Bank 2
P0008: Engine Position System Performance (Bank 1)

P0019 & P0018
- Dirty Oil
- Engine mechanical problems
- Timing belt jumped teeth

P0008
- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

The Engine Control Module (ECM) monitors the position of both camshafts and the crankshaft. The ECM performs a test for misalignment between both camshafts on one bank of the engine and the crankshaft. During the test the ECM learns the position of the camshafts and the crankshaft. While the engine is idling, the ECM compares the position of both the camshafts and the crankshaft with the learned value. The ECM will set the P0008 code if both learned values for one bank of the engine are exceeding a calibrated threshold in the same direction.

Feb 07, 2012 | 2005 Suzuki XL-7

1 Answer

I've 1995 eagle talon esi non turbo 2.0 dohe I was driveing it and it stooped running it will turn over but won't start what can Ido


check the timming belt. it sounds like you have broken the timming belt remove the belt cover and make sure that the camshafts are turning when you are cranking the engine, if the belt has broken you will most likly have to remove the cylinder head and replace all the valves, when this engine brakes the timming belt the valves will hit the top of the pistons and bend the valves...good luck

Dec 30, 2011 | 1995 Eagle Talon

3 Answers

I have a p0008 code & I'm worried


P0008 CADILLAC - Engine Positions System Performance Bank 1
The ECM detects that both camshafts on either bank of the engine are mis-aligned with the crankshaft for more than 4 seconds or a cumulative of 50 seconds.

The Engine Control Module (ECM) monitors the position of both camshafts and the crankshaft. The ECM performs a test for misalignment between both camshafts on one bank of the engine and the crankshaft. During the test the ECM learns the position of the camshafts and the crankshaft. While the engine is idling, the ECM compares the position of both the camshafts and the crankshaft with the learned value. The ECM will set the P0008 code if both learned values for one bank of the engine are exceeding a calibrated threshold in the same direction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

Tech notes
There is a factory service bulletin for the following Cadillac models:

2004-2008 Cadillac CTS SRX
2005-2008 Cadillac STS

The service bulletin suggest replacing the primary drive and both secondary drive timing chains. Contact your Cadillac dealer for more information. The repair could still be cover under factory warranty.


Hope this helps (remember to rate this answer).

Jun 02, 2011 | Cadillac SRX Cars & Trucks

2 Answers

Where are the timing marks on a 1996 Mitsubishi eclipse?


If you have the 4-Cylinder Non-Turbo, or 420a engine, here is the overhaul manual for it, including the complete timing instructions: http://www.mediafire.com/?7j2zosdmnnl

If you have the 4-Cylinder Turbo, or 4G63 engine, here is the manual for it, including timing instructions: http://www.mediafire.com/?zhnttihoqye

Mar 18, 2011 | 1996 Mitsubishi Eclipse

1 Answer

Im changing the timimg belt for my 1995 impreza because it broke, i know that when you are about to change it you must put marks but since it broke. How doi pu the engine back on time


There should be marks on the cambelt itself that align with the gogs markings. Best to start at Top Dead Centre (TDC) If the belt has broken then if that has not done damage to the valves I'd be surprised. If it is a turbo then the valves do touch pistons when out of sync. I have no knowledge about non turbo cars but I think the engine configuration is similar . To be honest it is best to get someone who is familiar with the cars to do it. Especially if it is a turbo. It is one car that requires knowledge and experience to do this particular job. The Cambelt is very long , goes over 4 camshafts , water pump plus guides and crank pully ect. That all needs precise alignment. No errors are acceptable so it is up to you. Think about it and read up before you do it.

Mar 05, 2011 | 1995 Subaru Impreza

1 Answer

TIMING BELT SCHEMATIC ON A 1999 MITSUBIHI ECLIPSE 2.0


Since you didn't specify if you had the turbo or non-turbo engine, i'll give you links to both.
2.0L non-turbo (420a) RS/GS
2.0L turbo (4g63) GST/GSX

Sep 04, 2010 | 1999 Mitsubishi Eclipse

1 Answer

Installing a timing belt


Timing Belt and Sprockets REMOVAL & INSTALLATION Fig. 1: If you plan on reusing the timing belt, make sure you note the direction of the rotation before removal 91053p69.jpg Fig. 2: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts 91053p10.jpg Fig. 3: Camshaft alignment using the special service tool 91053g61.gif Fig. 4: Insert the crankshaft damper bolt to turn the crankshaft and . . . 91053p64.jpg Fig. 5: . . . align the camshafts and the . . . 91053g64.gif Fig. 6: . . . crankshaft before removing the old belt 91053p66.jpg Fig. 7: Loosen the timing belt tensioner pulley bolt, slide the tensioner back and . . . 91053p67.jpg Fig. 8: . . . tighten the bolt to the farthest right hand side as possible to hold the release the tensioner pulley so that the belt can be removed 91053p68.jpg Fig. 9: . . . remove the belt starting from around the camshaft pulleys 91053p01.jpg Fig. 10: Installation of the tensioner spring and retaining bolt 91053g62.gif For information on timing belt recommended replacement interval, refer to Section 1. CAUTION
The 2.0L engine is an interference motor. Extending the replacement interval could lead to the belt breaking and severe and costly engine damage. Care must be taken if rotating the crankshaft or camshafts with the belt off, if resistance is felt, do not force them to turn.
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers as outlined in this Section.
  3. Remove the valve cover.
  4. Place Camshaft Alignment Timing Tool T94P-6256-CH or equivalent, into the slots of both camshafts at the rear of the cylinder head to lock the camshafts into position. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  5. Loosen the camshaft timing belt tensioner pulley retaining bolt and move the tensioner pulley to relieve the tension on the timing belt.
  6. Temporarily tighten the tensioner in this position. NOTE: If the timing belt is to be reused, mark the belt for the direction of rotation before removing to prevent premature wear or failure.
  7. Remove the timing belt.
  8. If required, remove the sprockets as follows:
    1. Hold the camshaft with an appropriate camshaft sprocket holding tool.
    2. Loosen and remove the camshaft sprocket retaining bolt.
    3. Remove the sprocket from the camshaft.
    4. Repeat the procedure for the 2nd camshaft sprocket.
    5. Remove the crankshaft sprocket.
  9. Slide the crankshaft sprocket onto the crankshaft aligning the key-way.
  10. Align the camshafts using the Camshaft Alignment Timing Tool T94P-6256-CH. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  11. Reinstall the sprockets onto the camshafts and loosely install the camshaft retaining bolts.
  12. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  13. Loosely install the crankshaft pulley to verify that the engine is at TDC. Realign the marks if they have moved.
  14. Verify that the camshafts are aligned. NOTE: It is recommended to purchase a tensioner spring and retaining bolt through the dealer parts to apply the proper tension for used or new belt installations. The spring is bolted to the tensioner assembly and becomes a part of the engine. Ignore this notice if the tensioner spring is already installed.
  15. Reinstall the retaining bolt (W700001-S309) into the hole provided in the cylinder block and place the tensioner spring (6L277) between the bolt and the camshaft timing belt tensioner pulley.
  16. Tighten the retainer bolt to 71–97 inch lbs. (8–11 Nm) .
  17. Remove the crankshaft pulley and install the timing belt onto the crankshaft sprocket, then onto the camshaft sprockets working in a counterclockwise direction.
  18. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  19. Be sure that the span of the camshaft timing belt between the crankshaft sprocket and the exhaust camshaft sprocket is not loose.
  20. Be sure that the camshaft timing belt is securely aligned on all sprockets.
  21. Reinstall the lower timing belt cover and tighten the retaining bolts to 53–71 inch lbs. (6–8 Nm) .
  22. Apply silicone sealer to the key-way of the crankshaft pulley and install. Tighten the retaining bolt to 81–89 ft. lbs. (110–120 Nm) .
  23. Inspect the timing mark on the crankshaft pulley to verify that the engine is still at TDC.
  24. Loosen the camshaft timing belt tensioner pulley retaining bolt and allow the tensioner spring attached to the pulley to draw the tensioner pulley against the camshaft timing belt.
  25. Remove the camshaft alignment timing tool from the camshafts at the rear of the engine.
  26. Turn the crankshaft two revolutions in a clockwise direction.
  27. Tighten the camshaft timing belt tensioner pulley retaining bolt to 26–30 ft. lbs. (35–40 Nm) .
  28. Recheck that the crankshaft timing mark is at TDC for the No. 1 piston, and that both camshafts are in alignment using the camshaft alignment timing tool. NOTE: A slight adjustment of the camshafts to allow the insertion of the camshaft alignment timing tool is permissible as long as the crankshaft stays at the TDC location.
  29. An appropriate camshaft sprocket holding tool can be used to move the camshaft sprocket (s) if a slight adjustment is required.
  30. If a camshaft is not properly aligned, perform the following procedure:
    1. Loosen the retaining bolt securing the sprocket to the camshaft while holding the camshaft sprocket from turning with the sprocket holding tool.
    2. Turn the camshaft until the camshaft alignment timing tool can be installed.
    3. Verify that the crankshaft timing mark is at TDC for the No. 1 cylinder.
    4. While holding the camshaft sprocket with the camshaft sprocket holding tool, tighten the retaining bolt to 47–53 ft. lbs. (64–72 Nm) .
    5. Remove the tool and rotate the crankshaft two revolutions (clockwise) .
    6. Verify that the camshafts are aligned and that the crankshaft is at TDC for the No. 1 cylinder.
  31. Install the valve cover.
  32. Install the timing belt covers.
  33. Connect the negative battery cable. prev.gif next.gif

Aug 17, 2010 | 2000 Mercury Mystique

1 Answer

I want more horse power without having to due an engine swap whats the best way to start everythings stock


start with intake manifold cold air intake not a short ram intake performance spark plugs wires and distributor cap, headers exhaust system not a tip.
make sure you have an LSD transmission then pull apart the motor mainly the head change out valves, spring retainers, and springs. new camshafts make sure you buy the springs and spring retainers before you put in the new cams. if you have the money to bore out the block it be better to take your block clean it up and put darton sleeves then buy a new crankshaft new psitons and rods with new rings all of this will cost a good deal but will increase performance a turbo should be the last thing you do increase the motor HP and max it out then put in a turbo but ensure your car is sleeved darton sleeves are the best never had a problem. i used to own a 2000 honda civic si i pushed 239 HP staright motor B16A2 motor. good luck any other questions let me know

Nov 03, 2009 | 1994 Honda Civic Del Sol

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...