Question about 1998 Isuzu Rodeo

1 Answer

Engine stops running after replacing the fuel sending unit.

Om my 2000 Isuzu I replaced the furl sending unit. Now the car
occasionally stops running when setting at idle. After two to three trys it starts fine and runs until it does it again. Anone having this problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Do you have the seal for the tank properly installed kinks or collapsed fuel lines and properly tightened? did you bang or drop fuel pump?good places to start!

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get fuel to carb on 94 Isuzu pickup after replacing fuel pump and filters , I try using starting fuel to let it crank up catch prime , it dies and has gas.


install the furl lines on the pump the other way around
if it is not pumping fuel you have the inlet as the out let and visa versa
look for an arrow on the pump housing and install accordingly

May 10, 2016 | Isuzu Cars & Trucks

1 Answer

Replace fuel pump om 1990 nissa 300zx


Sort of.
There should be a relay that provides power to the pump when you first turn the key on.
Then once the engine starts power is provided by way of the oil pressure switch. That way the pump won't run in an accident.
The oil pressure switch grounds the fuel pump relay on some models.

Jul 21, 2012 | 1991 Nissan 300ZX

1 Answer

Fuel sending gauge not reading right


the fuel sending unit is attached to the fuelpump, so the only way to fix it is replace the fuel pump assembly, sometimes they will make an aftermarket sender, you might want to check first.. but anyhow you can either replace it, or just keep track of your miles. hope this helps

Dec 03, 2010 | 2000 Isuzu Rodeo

1 Answer

Signifique code p-1627


Trouble code P1627 means: PCM A/D Conversion Malfunction

This is a fuel sending unit code and it directly related to you goofy gas gauge. This is a common problem in 2nd Gen Isuzus. The fuel sending unit needs to be replaced. Most places will tell you that you must replace the entire fuel pump assembly module but you can buy just the sending unit.

Other faults to refer this problem and other c
odes: P0141, P0300, P0404, P1404, P1627, with this synthoms:
hesitates sometimes on takeoff, gas gauge gives random readings(sometimes will read empty, or full, or somewhere in between), Fuel light flashes sometimes.

Hope helps.

Mar 16, 2010 | 2000 Isuzu Rodeo

1 Answer

Fuel gauge not working om golf3 gsx 98


Your sending unit inside the gas tank must be going bad. Have this professionally diagnosed and if it needs replacement use your highest judgment screening for a repair shop to do it. This is inside the fuel tank and a 99% things can go wrong left to someone unfamiliar with working this critical.

Jan 04, 2010 | 2000 Volkswagen Golf

1 Answer

2000 Isuzu Rodeo - the fuel light comes on but it is full of gas - is the sendding unit bad or what might be the problem


yes the fuel sending unit will need replacing, faulty fuel sender unit will give the guage inaccurate reading.

Nov 02, 2009 | 2000 Isuzu Rodeo

1 Answer

Smog test will not pass


This code is send (in your case NOT SEND)
by the fuel sending unit.

Does your fuel gauge give incorrect of jumpy reading when it's full?

The quick fix is STOP TOPPING OFF the fuel tank when you are get gas.

Keep topping off will push the fuel tank float off it's sensor limit and eventually short or send OUT OF RANGE reading to the fuel gauge.

Fill your truck up to 3/4 tank full.

Drive it for 2-3 days or about 100 miles.
(this will fill the ready-ness data that DMV want)

If there is NO check engine light ON during the 2-3 days then give the smog test another shot.

DO NOT add fuel unit you complete the smog test.
===

The CORRECT method to fix your problem is to drop the gas tank and replace the fuel sending unit.

If you truck has over 140,000 miles on it then I will recommend you the change the WHOLE integrated fuel pump/fuel sending unit and fuel filter at the same time.

Jun 02, 2009 | 1999 Isuzu Rodeo

1 Answer

I have a 2000 Isuzu Rodeo the gas gage is not reading correctly i fill it up and it reads empty and the gas light is on all the time.


The fuel level sending unit is located inside the fuel tank along with the fuel pump and will need to be replaced if it has burned out. It may be included with a new fuel pump assembly or sold seperately. There could be a bad electrical connection so be sure and check that all electrical connections are clean and secured before you spend money replacing parts and removing the fuel tank.

Apr 23, 2009 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...