Question about 1997 Nissan Quest

1 Answer

Location of camshaft sensor 1 for a 1997 Nissan Quest

I have a 1997 Nissan quest that was computer diagnosed that the camshaft sensor 1 had gone out in it. I am trying to fix this myself but I am not familiar with where to find it under the hood. Please advise.
Thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

Go to Auto Zone, get a Haynes manual on this vehicle. It will tell you where it's at and also help you with future problems.

Posted on Jan 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 nissan quest min van camshift sensor located


According to amazon.com,

CAMSHAFT POSITION SENSOR

1997 Nissan/Datsun Truck Quest Mini Van 3.0L FI SOHC 6cyl

The Camshaft Position Sensoris located: Under hood, passenger side, upper engine area, end of intake manifold, mounted in distributor

Sep 19, 2017 | Nissan Cars & Trucks

1 Answer

Location of the Camshaft Position Sensor "A" Circuit on 2004 Quest SE.


Sensor A is the sensor for the engine cylinder bank that is closest to the radiator.. I have attached a link you need to look at that shows the diagrams of the sensors, the sensor A is the one next to the nipple that the upper radiator hose connects to and is labeled "Bank Two" in the diagram.

Mar 28, 2017 | 2004 Nissan Quest

2 Answers

My 2004 Nissan quest and starts but when I'm


your timeing is out might need new timeing belt

Mar 24, 2012 | 2004 Nissan Quest

1 Answer

Camshaft censer are there two are macanic said they are not working


Yes, your 2004 Nissan Quest is equipped with 2 camshaft position sensors. If your computer is setting OBD fault codes for BOTH sensors, it is HIGHLY UNLIKELY that both of your cam sensors are bad. You most likely have a timing issue like a broken timing chain guide or camshaft phaser (IVT) that is not functioning properly.

Jan 19, 2012 | 2004 Nissan Quest

1 Answer

My 99 nissan quest will not get spark it died while idling in driveway timing belt is still working


change your coils or coil if not the issue your crankshaft postion sensor or camshaft postion sensor are faulty


if it helps please leave me thumbs up review

May 08, 2011 | 1999 Nissan Quest

1 Answer

1997 nissan quest camshaft sensor where is it & how to replace it


The camshaft sensor is located inside the distributor and is part of it, in order to replace it you must replace the distributor,to replace remove the dist cap. mark the location of the rotor,by marking where its pointing to, then mark the dist housing, so now theres a mark on the rotor and housing to show where rotor points, next mark the location of dist going into housing, mark the shaft and the block,because it spins in block this way you can line back up.next remove hold down bolt and pull out,mark the new dist in exacat same spots as the old so you can install back the same,you may have to put it in and pull it out until your marks are lined up,this way the timing will be dead on, when done you can check timing. good luck

May 09, 2010 | 2004 Nissan Quest

2 Answers

Where is the camshaft positioning sensor located in the 2004 nissan quest


Your 2004 Nissan Quest is most likely to be equipped with a 3.5L V-6 engine. This engine has 2 Cam (PHASE) sensors. One is located in the back of each cylinder head. You must remove your intake air duct to see them.

Oct 17, 2009 | 2004 Nissan Quest

1 Answer

2005 NIssan quest camshaft sensor


for a Nissan Quest, it is in the distributor. Not serviceable, replace distributor. Famous for nearing failing and getting brown dust on optical sensor for camshaft sensor. buy on ebay for $200. Cleaning optical sensor is temp repair.

Call dealer & see if yours is there too.

Jun 21, 2009 | 1997 Nissan Quest

Not finding what you are looking for?
1997 Nissan Quest Logo

Related Topics:

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...