Question about 1998 Isuzu Rodeo

1 Answer

1998 Isuzu Rodeo w/ 3.2l Water Pump

Does the engine need to be on TDC when changing out the water pump and timing belt?

Posted by on

  • Paul Broadhurst Jan 07, 2009

    Doesnt the timing belt come off when the pump is done due to the pump being timing belt driven?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Water pump,No
Timing belt,Yes

Posted on Jan 07, 2009

  • Randy Hough
    Randy Hough Jan 07, 2009

    Yes,but the water pump doesn't have to be set with the timing.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced water pump lined belt marks now the marks are off after turning motor over by hand


How to get my timing back correct after replacing timing belt.

www.cargurus.com > Questions > Dodge > Journey
CarGurusJan 18, 2015 - I have went in and replaced the water pump and the timing belt. ...Align the crankshaft sprocket (10) with the TDC mark (9) on the oil pump cover. 2. ...and then just shut off and won't restart? try unplugging the cam ... The two timingmarks for the camshafts are lined up and the crank is lined up with TDC.

Timing Belt Change - Miata.net


Nov 23, 2015 | Cars & Trucks

1 Answer

Shop says my 2002 Honda CR-V needs to have a camshaft position sensor replaced. Can you tell me where it's located and if I can replace it myself? I have some knowledge from working on my own vehicles. ...


The TDC sensor (aka camshaft position sensor) is located under the same cover as the timing belt. Incidently, the water pump is also driven by the timing belt. The process for replacement of the TDC is not difficult, just involved. Here is a link that I hope you will find helpful; It gives step-by-step instructions with photos on how to change the TDC. This is for a civic, but the setup for the CR-V is essentially the same. If you have high mileage, you will also want to check the condition of the timing belt and water pump while you have everything apart. If you decide to replace the other parts as well, you will need the associated gaskets, timing belt, water pump and belt tensioner. http://www.civicforums.com/forums/7-honda-civic-diys-civic-tech-chat/323984-diy-tdc-sensor-cmp-sensor-replacement-w-pics.html?8caa1db9f40a1e09f200d7c940d8cc64
If your computer will not let you click on the link directly, you can copy and paste it to your address bar.

Good luck and God Bless.

Apr 07, 2011 | 2002 Honda CR-V

2 Answers

How to change timing belt for honda pilot


Timmimg belts on honda vehicles are very in depth and on some models equiped with and balance shaft system require special tools ! It can be done at home but i highly recommend you purchase a repair manual that will give you a step by step instruction and i also recommend you change your water pump when doing this as well while everything is off the front of the engine ! Please note that all the engine Compoments must be timmed properly and in the right sequence or else engine damage can occur !

Mar 14, 2011 | Honda Pilot Cars & Trucks

1 Answer

How to change timing belt 2002 Mitsubishi mirage 1.5 standard trans


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and consider replacing the water pump at the same time. You will have to take off the power steering belt, the alternator belt, the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover, line up the tdc timing mark, take off the lower pulleys, take off the lower engine cover, take off the timing belt, counter balancer belt if there is one, water pump belt, and now you can unbolt the water pump, scrape the gasket, and replace it. Now the good news, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Sep 24, 2010 | Mitsubishi Mirage Cars & Trucks

1 Answer

How do i cange a timing belt on 03lancer oz rally timing belt needs to be changed


You should buy all new belts and a water pump for the car. You will have to take off the power steering belt, the alternator belt, the upper belt cover, support the motor, take off the motor mount, take off the front wheel , take off the engine under covers , line up the TDC timing mark(pulley to cover), take off the lower pulleys, take off the lower cover, take off the timing belt, water pump belt, and now you can unbolt the water pump, scrape the gasket, and replace it. If you put it back together , do not replace the water pump and it goes bad you will kick your self . Now the good news, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually save money and do it your self.

Sep 11, 2010 | 2003 Mitsubishi Lancer

1 Answer

I want to change the timing belt of my car. Can you give me detailed instructions on how to do it.


I have pasted the instructions from autozone.com below, but I never recommend this chore for a novice. If the valve timing is not right, it can ruin your engine. If you have not done this before, I recommend you at least have a mechanic look at the belt before you close up the timing cover.


Removal & Installation

1.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Note the radio security code and the radio presets. Disconnect the negative battery cable.
  3. Rotate the crankshaft to set the engine at Top Dead Center (TDC) on the compression stroke for the No. 1 piston. The white mark on the crankshaft pulley should align with the pointers on the timing cover. Once the engine is in this position, it must not be disturbed.
  4. Raise and support the vehicle safely. Remove the front tires. Remove the splash shield. Lower the vehicle.
  5. Remove the power steering pump and position it to the side without disconnecting the hoses. Remove the alternator.
  6. Remove the ignition coil cover. Remove the four ignition coils. Remove the throttle cable clamps and harness holder mounting bolts. Remove the cylinder head cover. Remove the crankshaft pulley.
  7. Properly support the engine using a block of wood under the oil pan. Remove the upper bracket.
  8. Remove the grommet from the upper cover. Disconnect the camshaft position (CMP) top dead center (TDC) sensor connector.
  9. Remove the side engine mount bracket.
  10. Remove the crankshaft position (CKP) sensor from the oil pump, without disconnecting the connector.
  11. Apply slight force to the timing belt at the midpoint between the camshaft pulley and the water pump pulley and check that the auto tensioner moves smoothly, if not replace it.
  12. Move the auto tensioner to remove tension from the timing belt. Remove the timing belt.
To install:
7ea3b6e.jpg
    Fig. TDC alignment mark locations for the crankshaft sprocket-1.7L engine




46a4de6.jpg Fig. Timing belt sprocket TDC mark positioning for timing belt installation-1.7L engine

  1. Set the crankshaft to TDC. Align the TDC mark on the timing belt drive pulley with the pointer on the oil pump.
  2. Set the camshaft to TDC. The UP mark on the camshaft pulley should be at the top. Align the TDC marks on the camshaft pulley with the top edge of the cylinder head.
  3. Install the timing belt in a counterclockwise sequence, starting with the drive pulley.
  4. As required, replace the auto tensioner assembly.
  5. Continue the installation in the reverse order of the removal procedure.
  6. Reprogram the ECM/PCM engine idle characteristics. Be sure all electrical items are OFF.
  7. Start the engine. Hold the idle speed at 3000 RPM-s in park or neutral until the radiator fan comes on or the temperature reached 194 degrees.
  8. Let the engine idle for about five minutes with the throttle fully closed.
  9. If the radiator fan comes on during the five minutes, do not count this toward the five minute programming time.
  10. Set the clock.

Sep 04, 2010 | 2002 Honda Civic

1 Answer

How to change a timing belt in a 2001 pt cruiser 2.4 liter


REMOVAL
  1. Disconnect negative battery cable.
  2. Raise vehicle on hoist. Remove right front wheel.
  3. Remove the right splash shield.
  4. Remove accessory drive belts.
  5. Remove crankshaft damper
  6. Remove the lower torque strut
  7. Disconnect exhaust system from manifold.
  8. Disconnect A/C pressure switch at rear of compressor housing.
  9. Lower vehicle and support engine with a jack.
  10. Discharge A/C system and disconnect A/C lines at coupling block
  11. Remove upper torque strut
  12. Remove screw attaching ground strap to strut bracket.
  13. Remove torque strut bracket from strut tower.
  14. Remove upper radiator support crossmember
  15. Remove power steering pump and bracket. Set pump aside. Do not disconnect lines from pump.</B>
  16. With engine properly supported, remove right engine mount through bolt.
  17. Raise engine with jack until engine support bracket bolts are accessible.
  18. Remove support bracket bolts.
  19. Remove support bracket.
  20. Remove upper timing belt cover fasteners and remove cover.
  21. Remove lower timing belt cover fasteners and remove cover
  22. CAUTION: When aligning crankshaft and camshaft timing marks always rotate engine from crankshaft. Camshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before removing timing belt.
  23. Before the removal of the timing belt, rotate crankshaft until the TDC mark on oil pump housing aligns with the TDC mark on crankshaft sprocket (trailing edge of sprocket tooth)
  24. NOTE: The crankshaft sprocket TDC mark is located on the trailing edge of the sprocket tooth. Failure to align trailing edge of sprocket tooth to TDC mark on oil pump housing will cause the camshaft timing marks to be misaligned.
  25. Install 6 mm Allen wrench into belt tensioner. Before rotating the tensioner, insert the long end of a 1/8” or 3 mm Allen wrench into the pin hole on the front of the tensioner .
  26. While rotating the tensioner counterclockwise, push in lightly on the 1/8” or 3 mm Allen wrench, until it slides into the locking hole.
  27. Remove timing belt. CAUTION: If timing belt was damaged due to incorrect tracking (alignment), the belt tensioner assembly must be replaced

INSTALLATION
  1. Set crankshaft sprocket to TDC by aligning the sprocket with the arrow on the oil pump housing.
  2. Set camshafts timing marks so that the exhaust camshaft sprocket is a 1/2 notch below the intake camshaft sprocket
  3. CAUTION: Ensure that the arrows on both camshaft sprockets are facing up.
  4. Install timing belt. Starting at the crankshaft, go around the water pump sprocket, idler pulley, camshaft sprockets and then around the tensioner
  5. Move the exhaust camshaft sprocket counterclockwise to align marks and take up belt slack. NOTE: A new tensioner is held in the wound position by a pull pin.
  6. Remove the pull pin or Allen wrench from the belt tensioner.
  7. Once the timing belt has been installed and tensioner released, rotate the crankshaft two (2) complete revolutions. Verify that the TDC marks on crankshaft and timing marks on the camshafts are aligned as shown in .
  8. Install lower timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
  9. Install upper timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
  10. Install right engine support bracket. Ensure the power steering pump is properly located in mounting location on bracket. Tighten mount bracket bolts to 61 N·m (45 ft. lbs.)
  11. Lower engine into mounting position and install right engine mount through bolt. Tighten bolt to 118 N·m (87 ft. lbs.).
  12. Install power steering pump and bracket.
  13. Install upper radiator support crossmember
  14. Install torque strut bracket to strut tower.
  15. Connect ground strap to bracket.
  16. Install upper torque strut
  17. Connect A/C lines. Evacuate and recharge A/C system
  18. Raise vehicle.
  19. Connect exhaust system to manifold.
  20. Connect A/C pressure switch connector.
  21. Install crankshaft damper
  22. Install accessory drive belts
  23. Install lower torque strut
  24. Perform torque strut adjustment procedure
  25. Install right splash shield.
  26. Install right front wheel.
  27. Connect negative cable to battery.

May 15, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Needing schematics for timing belt on a 2000 se


Removal & Installation

2.0L Engine
  1. Remove or disconnect the following:

    Negative battery cable Spark plugs Catalytic converter Right front wheel Right inner splash shield Accessory drive belt and idler pulley
  2. Rotate the crankshaft to Top Dead Center (TDC) and install Crankshaft TDC Timing Peg T97P-6000-A.
  3. Rotate the crankshaft clockwise against the peg.
  4. Remove or disconnect the following:

    Water pump pulley Valve cover Crankshaft pulley Timing belt covers
  5. Install Camshaft Alignment Timing Tool T94P-6256-CH into theslots of both camshafts at the rear of the cylinder head to lock thecamshafts into position.
  6. Loosen the timing belt tensioner bolt and relieve the tension onthe timing belt by disconnecting the tensioner tab from the timingcover back plate.
  7. Remove the timing belt.

    0900c152801e2a75.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Crankshaft alignment position-Ford 2.0L (VIN 3) engines


    0900c152801e2a76.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Placement of Camshaft Alignment Timing Tool T94P-6256-CH-Ford 2.0L (VIN 3) engines


    0900c152801e2a77.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Timing belt tensioner index marks-Ford 2.0L (VIN 3) engines

To install:

NOTE Always replace the timing belt after loosening or removing it.
  1. Install the timing belt.
  2. Engage the timing belt tensioner tab into the timing cover back plate.
  3. Adjust the timing belt tensioner until the index marks are aligned. Tighten the tensioner bolt to 17-20 ft. lbs. (22-28 Nm).
  4. Remove the camshaft alignment tool and the crankshaft TDC peg.
  5. Install or connect the following:

    Timing belt covers Crankshaft pulley. Tighten the bolt to 81-89 ft. lbs. (110-120 Nm). Valve cover Water pump pulley Accessory drive belt and idler pulley Right inner splash shield Right front wheel Catalytic converter Spark plugs Negative battery cable
  6. Start the engine and check for proper operation.

Apr 08, 2009 | 2000 Ford Contour

1 Answer

Water pump


Once you remove the timing belt covers,rotate engine,by hand via cranckshaft bolt (only in direction of normal engine rotation,i believe clockwise on that) and aligne all timing marks. At this time your engine is at #1 tdc..Follow manual and change belt.....Good Luck!!!

Sep 14, 2008 | 1993 Dodge Spirit

1 Answer

Water pump


You'll have to remove the timing belt covers, balancer and the water pump is actually turned by the timing belt. Be sure you place the engine on top dead center before you remove the belt. You'll have to place a jack under the engine because you'll have to remove the engine mount. By placing the engine on TDC, you'll have an easier time installing the timing belt. Replace the timing belt at the same time as the water pump. I call it cheap insurance.

Aug 17, 2008 | 1998 Plymouth Breeze

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14394 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...