Question about 1995 Jeep Grand Cherokee

1 Answer

Hello, I have a 1995 Grand Cherokee with a problem which is that I turned off at any moment, does not show a defined pattern that can be associated only turns off, then switched on without any problems. Could give me an idea of what has my vehicle. Thank you very much,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Sounds like the ECU /ECM connection.You will need to clean the connectors and add a very small amount of Dielectric grease


Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, how to relieve the belt tension on jeep grand cherokee 1995?


Hi,


In order to relieve the belt tension in your cherokee jeep,you have to locate the belt tensioner pulley first, which is found between the crankshaft and a component toward the top of the hood area.

Afterwards,Rotate the belt tensioner pulley, using a wrench spanner to relieve the tension on the belt.



Good luck.

Aug 20, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Hello. Where s the drain **** and the drain plug on jeep grand cherokee limited 1995?


Hi,

If you look under the engine you will see the drain plug at the rear of the engine sump.
You may need to remove the under belly shield to see it.

Hope this helps.

Thanks

Jason

Aug 17, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Swapping the 4.0 engine out of a wrecked 1995


No the tab bracket is different for your transmission

May 22, 2010 | 1993 Jeep Grand Cherokee

1 Answer

How to replace the intake manifold? I have a 96 grand cherokee v8, unable to replace the thermostat housing to the manifold because one of the screw holes cracked off on the manifold.


Position The Intake Manifold Gasket On The Engine.Dowels May Be Provided To Hold The Gasket In Place During Manifold Installation.. The Use Of Silicone Sealer Is Required. Especially Where The Front And The Rear Seals Meet The Side Gaskets On V-type Engines. Installing An Intake Manifold On V-type Engines Can Be Difficult. It Is Critical That You Use Sealer Properly On The Engine To Prevent Vacuum,Coolant, And Oil Leaks.

Start All The Fasteners By Hand Before Tightening. This Will Aid In Bolt Hold Alignment. Then Torque The Intake Manifold Fasteners To Specifications. Use The Specific Torque Pattern Given In The Service Manual.. Basically The Pattern Will Be A Crisscross Pattern

Apr 09, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Check engine on jeep grand cherokke 1995


Try again and verify, for example.
3 flashes,pause,then 3 more, is 33. etc.
5 flashes, pause 5 more, is code 55.(end of message)
always 2 digit number, then slightly longer pause in between those 2 digits.

Feb 23, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Engine code 95 jeep grand cherokee lerado


12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Dec 16, 2008 | 1995 Jeep Grand Cherokee

1 Answer

Code 53


Hello yeremya1776,

For Jeep Grand Cherokee, 1991-95 models:

Code 53 - Internal Controller Failure - Internal engine controller fault condition detected during self test

Hope this helps.

Remember: Good things come to those who Rate!!

Mike

Aug 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...