Question about 1994 Honda Accord

1 Answer

Broke timing belt on 94 accord LX

Need to know how to reset timing (Camshaft, crankshaft, ect...)

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Best thing to do is get a service manual, a Haynes manual has sufficient information for most service, including timing belt. Unfortunately, there is a good chance you have some bent valves because when the timing belt breaks, the pistons can hit the valves.

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Non interference


You say that you checked the timing marks (Camshaft vs. crankshaft) for proper alignment, but it's possible that the camshaft and crankshaft are out of sequence since the crankshaft turns two 360-degree rotations for every one of the camshaft. It's possible that the crankshaft needs to be rotated another 360 degrees and lined up with the timing mark on the camshaft (remove the timing belt in order to do this). Good luck.

Oct 04, 2013 | Mitsubishi Cars & Trucks

1 Answer

1991 honda accord lx backfires and cuts off after timming belt broke and repair what could be the problem with this car now


you need back to the timing belt and re_check the marks for the timing belt this are on the camnshaft and cranck shaft put on the EXACT position .I think is all what you need if is not explain with more details tnk.

Aug 28, 2012 | 1990 Honda Accord

1 Answer

How can i remove timing belt on 2005 kia sedona



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes

May 08, 2012 | 2005 Kia Sedona LX

1 Answer

I need a fan belt diagram for a 1994 bighorn


Timing belt installation

1. Ensure locking bolts located correctly [4] & [5] in the picture below:

tdisline_32.jpg
CS = Crankshaft
CA = Camshaft
IP = Injection Pump

2. Ensure timing marks aligned [10].
3. Fit timing belt in clockwise direction, starting at crankshaft sprocket.

NOTE: "ISUZU" lettering on belt should be readable from front of engine.

4. Slacken tensioner pulley bolt [9]. Push tensioner pulley against belt.
5. Ensure belt is taut between injection pump sprocket and tensioner pulley as well as crankshaft sprocket and camshaft sprocket.
6. Position tensioner lever [8] against tensioner pulley housing.
7. Remove locking bolts from sprockets [4] & [5].
8. Apply a load of 10 ... 12 kg to tensioner lever. Use spring balance [11].
9. Tighten tensioner pulley bolt to 80 Nm.
10. Turn crankshaft slowly 45 degrees anti-clockwise. Use spring balance to tension belt.
11. Repeat tensioning procedure at 45 degrees intervals for one anti-clockwise turn of the crankshaft.

NOTE: DO NOT turn crankshaft clockwise during tensioning procedure!

12. Fit tensioner lever to original position. Tighten nuts [12].
13. Install: Injection Pump flange [6], Camshaft sprocket flange [7], and water pump pulley.
14. Install components in reverse order of removal & refill coolant.
tdisline_33.jpg
Hope that helps. and good luck out there in the country side.

Apr 08, 2012 | Cars & Trucks

4 Answers

Need diagram to replace timing belt on 2000 dodge intrepid 3.5 engine


I Show Only a 3.2L For this Year this Will Guide you Enjoy your Work RejakWilson


REMOVAL

CAUTION: The following procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts. Refer to Camshaft Gear/Sprocket and Timing Components, if sprocket(s) or camshaft(s) have been loosened or removed.

CAUTION: The 3.2/3.5L are NOT freewheeling engines. Therefore, care should be taken not to rotate the camshafts or crankshaft with the timing belt removed.

  1. Disconnect negative cable from remote jumper terminal.
  2. Remove upper radiator crossmember.
  3. Disconnect fan module electrical connector.
  4. Remove cooling fan module and accessory drive belts.
  5. Remove crankshaft damper and front timing belt covers.
  6. Mark belt running direction, if timing belt is to be reused.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

f90f2f1.gif Fig. 94

  1. Rotate engine clockwise until crankshaft mark aligns with the TDC mark on oil pump housing and the camshaft sprocket timing marks are between the marks on the rear covers (Fig. 94).
CAUTION: Align the camshaft sprockets between the marks on rear belt covers before timing belt removal or damage to valve and/or pistons could occur.

  1. Using a ink or paint marker; mark the exact position of the camshaft sprocket timing mark relative to the two timing marks on the rear timing cover.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position

09766f9.gif Fig. 95

  1. Remove the timing belt tensioner (Fig. 95) and remove timing belt.
TIMING BELT TENSIONER

  1. When tensioner is removed from the engine it is necessary to compress the plunger into the tensioner body.
CAUTION: Compress the tensioner slowly, as damage to tensioner could result.

c719a3d.gif Fig. 96

  1. Place the tensioner into a vise and SLOWLY compress the plunger (Fig. 96). Total bleed down of tensioner should take about 5 minutes.
CAUTION: Index the tensioner in the vise the same way it is installed on the engine. This is to ensure proper pin orientation when tensioner is installed on the engine.

  1. When plunger is compressed into the tensioner body install a pin through the body and plunger to retain plunger in place until tensioner is installed.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position.

INSTALLATION

CAUTION: This procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts.

CAUTION: If camshafts have moved from the timing marks, always rotate camshaft towards the direction nearest to the timing marks (DO NOT TURN CAMSHAFTS A FULL REVOLUTION OR DAMAGE to valves and/or pistons could result).

a7cd673.gif
Fig. 97

  1. Align the crankshaft sprocket with the TDC mark on oil pump cover (Fig. 97).
  2. Align the camshaft sprockets (to reference mark made upon removal) between the marks on the rear covers (Fig. 94).
  3. Install the timing belt starting at the crankshaft sprocket going in a counterclockwise direction (Fig. 97). Install the belt around the last sprocket. Maintain tension on the belt as it is positioned around the tensioner pulley.
  4. Holding the tensioner pulley against the belt, Install the tensioner into the housing and tighten to 28 Nm (250 in. lbs.) . Each camshaft sprocket mark should still fall between the cover marks.
  5. When tensioner is in place pull retaining pin to allow the tensioner to extend to the pulley bracket.
  6. Rotate crankshaft sprocket 2 revolutions and check the timing marks on the camshafts and crankshaft. The marks should line up within their respective locations (Fig. 97). If marks do not line up, repeat procedure.
  7. Install timing belt covers and crankshaft damper.
  8. Install accessory drive belts and cooling fan module.
  9. Install upper radiator crossmember.
  10. Connect negative cable to remote jumper terminal.
  11. Start engine and allow to idle for approximately 1 minute. If a noise is present from the timing belt/tensioner, air has possibly entered the tensioner.
    1. To remove air from tensioner; using a DRB III, operate the engine at speed of 1600-2000 RPM for 10 minutes. This will purge air from tensioner.
NOTE: If air is present, the timing belt tensioner will be soft and may generate noise. This noise should disappear after no more than 15 minutes of engine running time.

Oct 21, 2010 | Dodge Intrepid Cars & Trucks

2 Answers

I need help to replace the timing belt well theres two rubbers its the lower rubber that broke. HELP PLEASE....


Well my friend first I need to know a little bit more. Now when you say rubbers, what do you mean? Your timing belt and gears consist of a cam shaft gear or sprocket, a crank shaft gear, and a tensioner located under the valve cover and behind the timing cover that is behind the crank shaft pulley. Can you help better understand which rubber thing broke?

Aug 18, 2010 | 1988 Toyota Pickup

1 Answer

Changing timing belt 01 civic lx


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2001/make/honda/model/civic/2001_honda_civic_timing_belt_diagram_marks.htm

Mar 22, 2010 | 2001 Honda Civic

1 Answer

Trying to put timing marks wright on a1995 ranger


Your question states both 94 and 95 for model year.
94 and 95 ranger had a 2.3L.

  1. If not done:
    1. Loosen tensioner adjusting bolt.
    1. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible.
    1. Tighten adjusting bolt to hold tensioner in released position.
  1. Align crankshaft so number one piston is at TDC (top dead center) with crankshaft key pointing straight up and circle on crankshaft sprocket (6306) aligned with notch in engine front cover (6019) .
  1. Align triangle on camshaft sprocket with triangle on inner timing belt cover.
  1. Align diamond on oil pump sprocket with diamond on inner timing belt cover.

    Timing Mark Alignment

5f171ff.gif

Feb 27, 2010 | 1994 Ford Ranger Supercab

1 Answer

Timming belt broke on 93 plymouth lazer and need instalation directions


It is recommended that the timing belt be replaced periodically to assure correct engine performance. Because of their composition, timing belts wear over a period of time and mileage. To avoid vehicle break down and possible engine damage, the manufacturer recommends timing belt replacement at 60,000 miles.
REMOVAL & INSTALLATION1.8L Engine
See Figures 1, 2 and 3
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt.
6dd1bcf.jpg

Fig. 1: Silent shaft belt timing marks-1.8L engine

b474c8c.jpg

Fig. 2: Checking the silent shafts for proper positioning

1b23c0f.jpg

Fig. 3: Timing belt timing mark alignment-1.8L engine

To install:
  1. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  2. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1 / 4 in.
  3. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  4. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  5. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover.
There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  1. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  2. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  3. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  4. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  5. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  6. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1 / 2 in.
  7. Install the timing belt covers and all related items.
  8. Connect the negative battery cable.
2.0L Engine
1990-94 VEHICLES
See Figures 4, 5, 6 and 7
  1. Disconnect the negative battery cable.
  2. Remove the timing belt upper and lower covers.
  3. Rotate the crankshaft clockwise and align the timing marks so No. 1 piston will be at TDC of the compression stroke. At this time the timing marks on the camshaft sprocket and the upper surface of the cylinder head should coincide, and the dowel pin of the camshaft sprocket should be at the upper side.
Always rotate the crankshaft in a clockwise direction. Make a mark on the back of the timing belt indicating the direction of rotation so it may be reassembled in the same direction if it is to be reused.

  1. Remove the auto tensioner and remove the outermost timing belt.

1f685f2.gif

Fig. 4: Exploded view of the timing belt and sprockets-1990-94 2.0L engines

  1. Remove the timing belt tensioner pulley, tensioner arm, idler pulley, oil pump sprocket, special washer, flange and spacer.
  2. Remove the silent shaft (inner) belt tensioner and remove the belt.
  3. Remove the crankshaft retaining bolts, then remove the pulley.
  4. Remove the crankshaft sprocket retainer bolt and washer from the sprocket, if used, and remove the sprocket. If the sprocket is hard to removed, the proper puller may be used. If no bolts are used on the sprocket. Use the correct puller to remove.
  5. Hold the camshaft stationary using the hexagon cast between journals No. 2 and 3 and remove the retainer bolt. Remove the sprocket from the camshaft.

To install:
  1. Install the sprockets to their appropriate shafts. Install the retainer bolts and tighten the camshaft sprocket bolt to 65 ft. lbs. (90 Nm).
  2. Check both tensioner and idler pulley for bearing wear, and replace if needed.
  3. Align the timing marks on the crankshaft sprocket and the silent shaft sprocket. Fit the inner timing belt over the crankshaft and silent shaft sprocket. Ensure that there is no slack in the belt.

79a47c7.jpg

Fig. 5: Align the camshaft sprocket so marks face each other and are in alignment with the top surface of the cylinder head-1990-94 2.0L engine

54d0ef5.jpg

Fig. 6: Align the crankshaft timing mark and the oil pump sprocket timing mark-1990-94 2.0L engine

73f137d.jpg

Fig. 7: Timing marks in alignment-1990-94 2.0L engine

  1. While holding the inner timing belt tensioner with your fingers, adjust the timing belt tension by applying a force towards the center of the belt, until the tension side of the belt is taut. Tighten the tensioner bolt.
When tightening the bolt of the tensioner, ensure that the tensioner pulley shaft does not rotate with the bolt. Allowing it to rotate with the bolt can cause excessive tension on the belt.
  1. Check belt for proper tension by depressing the belt on its' long side with your finger and noting the belt deflection. The desired reading is 0.20-0.28 in. (5-7mm). If tension is not correct, readjust and check belt deflection.
  2. Install the flange, crankshaft and washer to the crankshaft. The flange on the crankshaft sprocket must be installed towards the inner timing belt sprocket. Tighten bolt to 80-94 ft. lbs. (110-130 Nm).
  3. To install the oil pump sprocket, insert a Phillips screwdriver with a shaft 0.31 in. (8mm) in diameter into the plug hole in the left side of the cylinder block to hold the left silent shaft. Tighten the nut to 36-43 ft. lbs. (50-60 Nm).
continue...

Sep 09, 2009 | 1993 Plymouth Laser

4 Answers

1996 HONDA ACCORD CRANKSHAFT SENSOR AND CAMSHAFT SENSOR.


camshaft sensor is in distributor(requires dist. replacement) crankshaft is behind lower timing belt cover

Dec 12, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...