Question about 2000 Honda Civic

2 Answers

What size is the rear spindle nut on a '98 Honda Civic LX

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 22,041 Answers

Either a 30mm or 32mm

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why doesn't this 2000 Honda civic lx turn over when everything else works inside the car?


Honda Civic Coupe Questions - car will not start. battery ok ...

www.cargurus.com > Questions > Honda > Civic Coupe

CarGurusJul 9, 2008 - Get someone to turn it over and see if it is getting spark. ... i have the same issue with my 1993 civic lx it has a 1.5 sohc non-vtec i changed ... comes wen the 2nd click of the main relay it doesn't occurs until after few minutes, few .... My 2000 Honda Civic Ex Vtec will not start, has a new tps, new throttle body, ...

Part 1 -How to Troubleshoot a No Start (1.6L Honda Civic)

troubleshootmyvehicle.com > Honda > 1.6L
Dec 31, 2012 - Difference Between a No Start and a No Crank Condition. ... can cause your 1.6L Honda Civic (Civic del Sol) to Crank but Not Start. ... In other words, the engine doesn't turn over at all. ... 1995, 1996, 1997, 1998, 1999, 2000.

98 Honda civic won't crank (PushStart) - YouTube

? 4:11
https://www.youtube.com/watch?v=X5W7OqjKB8I
Oct 21, 2013 - Uploaded by SkzDaniel
Honda Civic won't start or crank with the clutch but goes on when you push start it. ... 2000 Honda Civic LX with new battery and starter. Still will ...

2000 Honda Civic LX with new battery and starter. Still will ...

? 6:34
https://www.youtube.com/watch?v=p7KAO__nM1s
Aug 21, 2013 - Uploaded by Robert SnyperMD
2000 Honda Civic LX with new battery and starter. Still will not start. ... Crank, No Start Diagnosis Honda Coil test. - Duration: 11:17. by ...

Jan 05, 2016 | Honda Cars & Trucks

1 Answer

I need help replacing a right upper control arm on my 98 civic si


jack up vehicle ,remove tire/wheel,separate upper ball joint from steering spindle. next open hood, look at the right front strut mount. there is a nut on each side of the strut mount, these nuts hold the upper control arm to the vehicle. remove the nuts and pull the control arm out. install in reverse procedure. NOTE: need to have alignment checked after replacement.

Aug 14, 2011 | 1998 Honda Civic

1 Answer

What socket do i need to remove the rear spindle nut on a 1990 honda civic


i believe its a 32mm or a 36....but im more to 32mm..... hope this helps

Sep 03, 2010 | 1990 Honda Civic

1 Answer

How do i remove a front axle spindle nut off my 2001 honda civic lx


Unstake the nut and turn left, a impact wrench is needed, be sure to torque the nut when putting it back together, 135 ft lbs.

Feb 05, 2010 | 2001 Honda Civic

1 Answer

My 98 honda civic Lx wont shift into gear


check your shift linkages if the bushing is worn out you may have problems shifting or it could be a bad transmission

Dec 25, 2009 | 1998 Honda Civic

1 Answer

Broken lug nut stud on 98 civic dx coupe


knock it out... use an old nut that will fit the new stud and install the stud. the nut will pull the stud in tight to the flange.

Jul 19, 2009 | 1998 Honda Civic

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic


Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

May 23, 2009 | 1994 Honda Civic

5 Answers

I need to replace upper right ball joint, 98 honda civic


This is a pretty easy job.The way i do it is take the two 14mm bolts louse from the strut on the inner fender well,then take the 17mm bolt out of the bottom of the strut on the lower control arm this will make it drop down.Then take the 14mm bolt louse that fastens the ball joint to the spindle take a hammer and hit the upper spindle and it all will come apart.Now you will have the two bolts that holds the upper control arm in place these are 17mm bolts drop the strut down and remove the upper control arm now you can go in with the new one.Hope this helps !!!

Mar 19, 2009 | 1998 Honda Civic

Not finding what you are looking for?
2000 Honda Civic Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...