Question about 2002 Ford Windstar Cargo

1 Answer

Oxy sensor light on, and also heat is not working. I dont know

I dont know where the sensors are located. please help

Posted by on

  • fmramirez Jan 12, 2009

    thank you so much, this is a van, not cargo, but I believe the mechanics are the same., and it was the speed sensor, thanks again, we had to replace them. Now the heat not working, we are going to check it out ourselves. , GREAT HELP, THANKS



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 123 Answers

Oxygen sensors are located on the exhaust pipe in front and behind the catalytic convertor. There are more than one. If your check engine light is on, the code will tell you which sensor is faulty - I need that code to tell you the exact location.
Also really need to know the engine type to be more specific.
If your heat is not working there is probably a fault in the door mechanism that lets air pass over the heat exchanger under the dash. the switch is most likely at fault.

Posted on Jan 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Po131 is the code for the oxy sensor, the voltage is low to the sensor. The sensor is the bank 1 senor and I do not know where the is for sure so you can goggle the oxy sensor for bank one and it will tell you where it is. You will need to replace it . Hope this helps .

Sep 19, 2015 | Cars & Trucks

1 Answer

1998 dodge 1500 rejected smog test

you really need to drive it for min of 30 minutes before you go, they need time to heat up and run a cycle,

Dec 06, 2013 | 1998 Dodge Ram 1500 4WD

1 Answer

Where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8

pic-1681384701591865649-tmb.jpegCrank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
front side of engine on the drives side about half way up the timing cover, not hard to get to.

Nov 11, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

Engine management light on ,car still runs perfect

check for fault codes in ecm at a guess knowing this model well it will have logged a code for heated oxy sensor faults sometimes you clear the codes and they dont come back.if the light comes back then one or more sensors are faulty more than likely open cicuit heater element in the sensors there are 2 or 4 sensors on that engine depending on market spec. the norm is 4 you can compare the sensors with a multimeter to locate the faulty ones ideally you need a wiring diagram to do this. genuine jaguar ones are expensive i have changed all 4 in the past to cure this problem at a cost off over 1000 pounds the other likley causes are throttle body problems and air leaks but you normally get restricted performance warning showing hope this helps been a jag tech for almost 50years

Mar 25, 2013 | 2001 Jaguar XJ8

2 Answers

Code p0133 on 2004 deawoo matiz please is it the oxy sensor and if so front or rear one thank you

O2 Sensor Circuit Slow Response Bank 1 Sensor 1
this is the sensor that is located in the exhaust just off the engine and before the cat converter, so it is the front sensor.

Oct 20, 2009 | 2002 Daewoo Nubira

2 Answers

Sears did a computer eval on our car and gave us codes only

P0135--OXY SENSOR HEATER CIRCUIT(bank 1 sensor 1)
P0141--OXY SENSOR HEATER CIRCUIT(bank 1 sensor 2)

Here are the code definitions.hope it helps.

Nov 15, 2008 | 1997 Mercury Cougar XR7

1 Answer

1990 honda accord

If it is a three wire ox sensor then you must make sure that wires are hooked up right or it will not function and cause engine to run erratic. One of the wires are for the preheater in ox sensor so it must be hooked properly.

Aug 09, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides