Question about 1997 GMC Jimmy

1 Answer

Rocker arm adjustment

I am looking for directions to adjust the rocker arms on a 1997 GMC Jimmy., or a web site to give me step by step instructions

Posted by on

  • kcorson2003 Jan 07, 2009

    NEED MORE OF A STEP BY STEP DESCRIPTION...OR A WEB SITE...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 78 Answers

Climers Moter manual has the drirections you need. You just turn the moter, untill both valves are closed. Turn the push rod as you tighten the rocker nut. When the puss rod quits turning, Give the nut on thr rocker on another half turn and your done. Only 15 more to do.

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok so ik I'm posting allot haha but does anyone know where or how to adjust lifters just found out mine r just now needed adjustment in near mount Vernon WA or a price at least haha


In engines with rocker arm valve systems, the procedure I'm familiar with is to remove a rocker arm cover, and (one at a time!) while the engine is running, slowly back off the rocker arm retainer nut or bolt just until you hear the lifter tapping, then tighten it a quarter turn. If you can identify a lifter that is already tapping, tighten its rocker arm slowly until it stops tapping, then adjust it. Do not over-tighten! This can damage the engine.

Listen carefully to how the engine sounds; if it starts to stumble when you tighten a loose rocker arm, you've gone too far. If you cannot get the engine to run well without tapping, you may have too much wear in the valve train and may be due for a head overhaul, or you don't have adequate oil pressure in the lifters in question.
Repeat until all rocker arms are done. Replace the rocker arm cover using a new gasket, then (in a V-engine), repeat the procedure on the other side of the engine.

Wearing safety goggles, or better yet, a transparent face shield, is strongly recommended. Sometimes oil will squirt out a considerable distance from the lifter side of the rocker arm during adjustment, and the direction is not readily predictable.

Apr 03, 2015 | Cars & Trucks

1 Answer

Adjust rocker arms on 1990 2.9 ford


this is from the AutoZone web site.

2.9L Engine
No periodic valve lash adjustments are necessary on this engine. The engine utilizes a hydraulic valvetrain to automatically maintain proper valve lash. However, some earlier models have an adjusting screw on the rocker arm, which is used when assembling the engine to properly preload the lifter. If the engine has been disassembled, and the valve train parts were not kept in order, or there is an audible sound from the rocker arms while the engine is running, perform the adjusment procedure below.
The following procedure should be performed on a cold engine.
  1. On the cylinder to be adjusted, position the cams so that the tappets are in the base circle area.
  2. Loosen the adjusting screws until a distinct lash between the roller arm pad and the valve tip can be noticed.

The plunger of the hydraulic tappet should now be fully extended under the load of the internal spring.
  1. Carefully screw in the adjustment screws until the roller arms slightly touch the valves.
  2. To achieve the normal working position of the plunger, screw in the adjusting screw 1 1 / 2 turns, equivalent to 2mm.


  3. here is the site address. scroll down the page & you will see your engine size - 2.9
SAVE 20 GET BONUS 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

Feb 06, 2015 | Ford Cars & Trucks

1 Answer

Where is the rocker arm on K1500 GMC 5.7L


what is the torque spec for rocker arm on 1994 gmc 5.7 liter,or how do you adjust them

Jan 19, 2013 | 1997 GMC Sierra

1 Answer

Well we tried adjusting the valves and then it will start and make a werid noise and then will be about to shut off and it doesnt sound right plezz can you help me? its a 1997 gmc 5.7 1500


With the Engine in the number 1 firing position, adjust the exhaust valves for cylinders number 1, 3, 4, and 8 and the intake valves for cylinders number 1, 2, 5, and 7.
Turn the valve rocker arm nut counter clockwise until the valve lash is felt in the valve pushrod.
Turn the rocker arm nut clockwise until all of the valve lash is removed (zero valve lash).
Zero valve lash can be felt by moving the valve pushrod up and down between your thumb and forefinger until there is no more up and down movement of the valve pushrod.
When all the valve lash is removed, then turn the valve rocker arm nut clockwise 1 additional turn (360 degrees).


With the engine in the number 6 firing position, adjust the exhaust valves for cylinders number 2, 5, 6, and 7 and the intake valves for cylinders number 3, 4, 6, and 8.

Follow the same steps as above.

Apr 01, 2011 | GMC Suburban Cars & Trucks

1 Answer

Rocker arm torque specs on a 97 gmc jimmy 4.3


  1. For the 4.3L engines which are equipped with screw-in type rocker arm studs with positive stop shoulders, tighten the rocker arm adjusting nuts against the stop shoulders to 20 ft. lbs. (27 Nm) on 1994-96 models and 18 ft. lbs. (25 Nm) on 1997-99 models. No further adjustment is necessary, or possible.
  2. For most 4.3L engines which are not equipped with screw-in type rocker arm studs and positive stop shoulders, properly adjust the valve lash. For details on valve lash adjustment, please refer to the procedure in Routine Maintenance . (see below)
4.3L Engine

The 4.3L engines may be equipped with either of 2 rocker arm retaining systems. If your engine utilizes screw-in type rocker arm studs with positive stop shoulders, no valve lash adjustment is necessary or possible. If however, you engine utilizes the pressed-in rocker arm studs, use the following procedure to tighten the rocker arm nuts and properly center the pushrod on the hydraulic lifter:
  1. To prepare the engine for valve adjustment, rotate the crankshaft until the mark on the damper pulley aligns with the 0? mark on the timing plate and the No. 1 cylinder is on the compression stroke. You will know when the No. 1 piston is on it's compression stroke because both the intake and exhaust valves will remain closed as the crankshaft damper mark approaches the timing scale.

Another method to tell when the piston is coming up on the compression stroke is by removing the spark plug and placing your thumb over the hole, you will feel the air being forced out of the spark plug hole. Stop turning the crankshaft when the TDC timing mark on the crankshaft pulley is directly aligned with the timing mark pointer or the zero mark on the scale.
The valve arrangement is as follows:



E-I-I-E-I-E (right bank-front-to-rear) E-I-E-I-I-E (left bank-front-to-rear)

  1. With the engine on the compression stroke, adjust the exhaust valves of cylinders No. 1, 5 & 6 and the intake valves of cylinders No. 1, 2 & 3 by performing the following procedures:
    1. Back out the adjusting nut until lash can be felt at the pushrod.
    2. While rotating the pushrod, turn the adjusting nut inward until all of the lash is removed.
    3. When the play has disappeared, turn the adjusting nut inward 1 3 / 4 additional turns.

  2. Rotate the crankshaft one complete revolution and align the mark on the damper pulley with the 0? mark on the timing plate; the engine is now positioned on the No. 4 firing position. This time the No. 4 cylinder valves remain closed as the timing mark approaches the scale. Adjust the exhaust valves of cylinders No. 2, 3 & 4 and the intake valves of cylinders No. 4, 5 & 6, by performing the following procedures:
    1. Back out the adjusting nut until lash can be felt at the pushrod.
    2. While rotating the pushrod, turn the adjusting nut inward until all of the lash is removed.
    3. When the play has disappeared, turn the adjusting nut inward 1 3 / 4 additional turn.

Sep 23, 2010 | 1997 GMC Jimmy

2 Answers

Why can't i adjust the rocker arms on a 2.2 1997 chevy cavalier? Are they self adjustable?


if the car has variable valve timing then yes you cant adjust rocker arms they are set with the timing and are probaly hydrolic not mechcanical good luck

Oct 16, 2009 | 1997 Chevrolet Cavalier

1 Answer

Can the rocker arms of a 1997 jeep grand cherokee straight six be adjusted


Remove the valve covers. Inspect each rocker arm for wear, cracks or other damage, check the rocker arm abd dykcrum for wear, replace with new ones, they can"t be adjusted.

Jul 01, 2009 | 1997 Jeep Grand Cherokee

1 Answer

How to adjust rocker shaft on discovery td5


There are adjustment screws on the rockets according to RAVE.
The procedure is as follows:
1) Rotate the engine clockwise until No 1 injector lobe is at full lift.
2) Rotate rocker adjusting screw clockwise until the injector plunger is felt to bottom out.
3) Rotate rocket adjusting screw anti-clockwise one complete turn to give plunger the required bump clearance and tighten rocker arm adjusting screw locknut to 16Nm. Ensure the screw does not turn as the locknut is tightened.
4) Carry out the procedure for the remaining 4 rocker arms.
5) After completion of rocker arm adjustment slowly rotate engine clockwise 2 complete turns by hand to ensure that no injectors are bottoming out on their plungers.

Apr 08, 2009 | 2003 Land Rover Discovery

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...