Question about 2005 GMC Yukon Xl Denali

1 Answer

Engine Oil Life

When i start my Yukon XL Denali it tells me engine oil life 0%, what does it mean?

Posted by on

  • abujabal Jan 21, 2009

    if stell the proplam replas oil level sensor located r/oilband yousuf



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

Change Your Oil And Filter Then Remove The Negative Battery Cable To Reset It.

Posted on Jan 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2007 Yukon xl denali burning oil

If you smell burning oil, you may have a leak in the engine compartment reaching the exhaust manifold and burning on contact. The most common cause for that is leaking valve cover gaskets. If you are losing oil with NO signs of external leaks, the engine may be burning it internally. Valve stem oil seals, worn piston rings, blown/leaking head gasket are a few causes of that.

Oct 07, 2012 | 2007 GMC Yukon XL Denali

1 Answer

I have a 2005 GMC Yukon Denali with 88,000 miles on it, when i first purchased the truck earlier in the year, the oil pressure gauge was reading all the way to 80, now when i press on the accelerator the...

Yes, most likely it is a defective oil pressure sending unit. However, oil pressure is something you do not want to take chances with. Have it checked with a manual gauge to determine the problem as soon as possible to avoid possible major engine failure. I hope this helps.

Aug 02, 2011 | 2005 GMC Yukon Xl Denali

1 Answer

Need to reset oil life indicator on 2005 GMC Yukon Denali after an oil change...How do I do that please??..THANKS!

it depends........ if you have controls on the steering wheel or not. If you do, then go through the menu until you see OIL LIFE then hold in the reset button (looks like a backwards "L" with an arrow on it). Hold the reset button in until it reads OIL LIFE RESET or OIL LIFE 100%. If you don't have controls on the steering wheel, turn key on (engine off) and depress the gas pedal to the floor 3 times, now turn key off. crank engine up and see that it has reset, if not try it again.

Dec 21, 2010 | GMC Denali Cars & Trucks

1 Answer

Just had my oil n filter changed but my trucks computer still states the engine oil life at 4% how do i reset this?

The oil life has to be reset it is done by turn the ignition key to the run with engine off. Fully press and release the gas pedal slowly thre times within 5 seconds. If the oil life reset message flashes for 10 seconds it worked. then turn the key to lock and test to make sure. I retyped this out of a manual but it does say press slowly I always did it fast from the time you turn that key on you have 5 seconds to pump that peadle 3 times to me thats not slow also for some reason I pumped 4 time then hold to the floor. It always worked. The procedure is supose to be in the owners manual if you have any problems look in there.

Oct 19, 2010 | 2006 GMC Yukon Denali

1 Answer

We changed the oil on our 2004 denali but we don't know how to reset the oil life percentage option

The instructions on how to reset the Life Percentage should be outlined in your Owner's Manual.

Jun 25, 2010 | 2002 GMC Yukon Denali

1 Answer


look in the manual......turn the ignition to the on position not starting it of course and then pump the gas petal 5 times then the light will blink a few times turn off then back on...problem solved

Jan 30, 2010 | 2002 GMC Yukon Denali

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction

Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

2 Answers

Changing the oil life from 0% to 100%...can't seem to fix... any suggestions?

What do you mean? changing the oil life.You change your oil by removing the plug on the bottom of the engine,let it all come out, drain.Replace the plug,then refill through the top of the engine.Fill with the right amount of fluid.

Jul 24, 2009 | 2007 Suzuki XL-7

1 Answer

How to reset computer showing percentage of oil life remaining

If it is anything like the 2003 you turn your car to the on position without running the engine, tap the accelerator 3 times very quickly in less than 5 minutes. This should reset your back to 0 for your next oil change.

Apr 03, 2009 | 2003 GMC Yukon XL

1 Answer

2000 yukon xl

turn the key to the run position engine off, push the gas pedal all the way to the floor then release it 3 times within 5 seconds, the DIC will say oil life reset.

Nov 05, 2008 | 2000 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides