Question about 1999 Isuzu Rodeo

1 Answer

Truck turns wide

1999 rodhe eo, when steering the vehicle and making turns I can poping, like there is a bolt stripped in the steering column.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Your CV joints are worn, not a hard job.. easier to see a mechanicf tho, not too expensive

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition lock cylinder


This may or may not help,but i found this

REMOVE OR DISCONNECT

1. Disable the SIR System.
2. Battery negative cable.
3. Knee bolster and IP steering column reinforcement. NOTICE: The steering column should never be supported by only the lower support bracket alone, damage to the column lower bearing adapter could result.
4. Lower support bracket from vehicle (2 bolts).
5. Upper column support from IP (2 bolts).
6. Lower steering column so that it rests on the driver seat.
7. Ignition switch wiring protector.
8. Ignition switch retaining screw and nut.
9. Ignition and turn signal switch column harness connectors from IP harness.
10. Turn signal switch connector from column harness.
11. Ignition switch, harness, and connector. Important

o DO NOT splice ignition switch wires.

INSTALL OR CONNECT

1. Ignition switch, securing with retaining screws.

o Adjust ignition switch. Steering Column Unit Repair.

2. Turn signal switch connector to column harness.
3. Ignition and turn signal switch column harness connectors to IP harness.
4. Ignition switch wiring protector.
5. Raise steering column to support bracket.
6. Two bolts to upper support bracket. Do not tighten fully at this time.
7. Bolt and nut to lower support bracket.

o Align column to instrument panel opening. A small shim (wedge) placed between the instrument panel column support bracket and the column can be used to hold the column stationary while tightening the upper support bolts.
o Upper and lower column support bolts and nuts to 27 Nm (20 ft. lbs.).

8. IP steering column reinforcement plate and knee bolster.
9. Battery negative cable.
10. Enable the SIR system.
super vag k+can v4.8

Jul 30, 2012 | 1994 Geo Prizm

1 Answer

Diagram for removing of steering column for 1988 gmc 2500 pickup 3/4 ton


Remove two bolts under the dash the hold column to lower dash support, reach under and disconnect the wiring near bottom and then pull back the sound deadening and remove the bolts from the inner bulkhead, go under the hood and remove the rag joint coupler bolts, then remove the column from the truck with care to make sure you didn't miss any thing before you man handle it out like the shift indicator cable is so equipped..

Jul 22, 2012 | Cars & Trucks

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

2 Answers

I`ve replaced my steering column and my car won`t start? Do I have to reprogram my computer or something?


Double check the wiring to the ignition unit and make sure everything is still lined up correctly.

Oct 28, 2010 | 1995 Buick Riviera

1 Answer

Steeringwheelto muchplay


You need to take apart the steering column after disconnecting the battery cable and once you're deep enough in the column, you should be able to locate a few bolts that connect the steering column to the rest of the vehicle. Tighten those down and the reassemble the steering column. Reconnect the battery and give it a test drive.

Mar 11, 2010 | 1999 Chrysler 300M

2 Answers

Very loose steering coulum on 1993 chevy truck can it just be tightened


There is a lower support and an upper support. Each support has 2 bolts. You will need to remove the driver's side knee bolster and the reinforcement plate behind it to access the support bolts. WARNING: always use extreme caution when working in the vicinity of airbags, if you aren't fully confident of proper safety procedures you could seriously injure yourself.

Jan 02, 2010 | 2000 Chevrolet Silverado

3 Answers

1989 GMC Sierra 3500 loose tilt steering column


Watch videos on youtube ( repairing loose tilt wheel)

Jul 19, 2009 | GMC Sierra 1500 Cars & Trucks

2 Answers

How to put on ignition switch on a '88 mazda b2200


If you mean actually replacing the ignition switch on the vehicle with a locking column. You need to do this. Dicconnect the battery, remove the lower panel of the dash if there is any. There is a bolt on the steering column near the fire wall on most vehicles, remove this bolt, it will release the spline on the steering column. Disconnect all wiring going to the column, unbolt the column from the dash support. Remove the column from the truck, on the ignition switch you will see where the two shear bolts screw the assembly together, center punch the center of each bolt. Now drill the bolt with a 1/8" drill about 1/4" to 3/8" deep. Now use a 3/8" drill and drill out the shear head until it comes off the bolt. You can now remove the switch assembly from the column. The new assembly should come with new shear off bolts so when you bolt it in place when tightned they will break off rendering it tamperproof again. Most vehicles are designed like this now to stop theft. Check the column for operation before reinstalling it in the reverse of above. You just want to make sure the key locks and unlocks the column before reinstalling in the vehicle. You may want to do this before you totally tighten the bolts and break them off permanently. Good luck, RAC

Mar 28, 2009 | 1988 Mazda B2200

1 Answer

Moaning noise in steering column


The probably lubed the intermediat shaft conenction. The loud poping noise could be from them not sitting the boot back correctly. Inspect your boot. As for the moaning noise Only thing I can think of is a hydraulic noise.

Dec 11, 2008 | 2007 Saturn Outlook

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...