Question about 1997 Toyota Camry

1 Answer

I have a 93 Camry. I am replacing the drivers side half shaft with the cv joint on it. Went and got the slide hammer and put it on the end. It pulled the half shaft apart and not out. How do I get it out?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

There should be a wire clip on the shaft

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Half shaft removal


The trick is to pop the circlip on the end of the axle shaft out of its groove in the transmission gears. Shops use a fork on the inner CV joint housing, attached to a slide hammer.
What usually works is to use a pry bar or large screwdriver between the CV housing and the transmission case, and pop the axle out. Be careful of damaging the axle seal on the transmission.

Jun 20, 2013 | 1992 Cadillac DeVille

2 Answers

How do you remove the cv joint on the left side from the transmission?


YOU NEED A PULLER ON THE OUTSIDE WHEEL HUB PUSHING THE HALF SHAFT FROM THE FRONT HUB,THEN TAP THE SHAFT UNION AT THE JOINT CASE WITH A PLASTIC HAMMER TO REMOVE THE HALFSHAFT AND INNER SHAFT FROM THE TRANSAXLE. IF YOU HAVE AN INNER SHAFT REMOVE THE HALFSHAFT BY SETTING UP A PULLER ON THE OUTSIDE WHEEL HUB AND PRESSING THE HALFSHAFT FROM THE FRONT HUB. AFTER PRESSING THE OUTER SHAFT INSERT A PRYBAR BETWEEN THE TRANSAXLE CASE AND THE HALFSHAFT AND PRY THE HALF SHAFT FROM THE TRANSAXLE DONT PULL ON THE SHAFT.

Sep 11, 2011 | 2001 Mitsubishi Eclipse Spyder

1 Answer

Is there a c clip in the front driver side holding the half shaft in on a 05 ram 2500 diesel. Trying to replace universal!


There is a spring-type C-clip on the end of the CV housing spline shaft. Disengage the CV joint from the axle housing by using a pry bar between the CV joint and the axle housing. It can be pretty tough to get it to let go. I have found it helpful at times to place the end of a pry bar on the back of the CV housing (as good as I can) and smack it with a BIG hammer. Putting it back in is not nearly as hard.

Jul 09, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

How do you get the left front cv's and half shaft out of the transmision?


there is a c-clip on the end of the axle that locks into a grove in the axle gear, they can fit pretty tight, some times you have to wrap a cable arond the in-board CV joint and aitches the cable to a slide hammer and give it a good pop, they do make a puller for the this purpose but it does just what i have told you to do. also some times you have to remove the other side axle and use a long screwdriver to go threw the trans-axle and push the axle out. most of the time you can just use a long chisel and put the tip on the lip of the CV joint and hit it with a hammer.

Apr 14, 2011 | 2001 Pontiac Bonneville

2 Answers

How do i replace wheel side cv joint boot


YOU CAN GET A BOOT REPAIR KIT OR A ZIP BOOT.DO NOT LIKE ZIP BOOT,DOESNT WORK . BEST TO GET A REMANUFACTURED AXLE AND REPLACE AS A UNIT,DOESNT COST MUCH MORE AND WIL WORK WITH A WARRANTY.TAKE OFF WHEEL,LOOSEN AXLE NUT,TAKE OFF LOWER BALL JOINT,POP AXLE WITH HAMMER TO DRIVE AVLE OUT OF BEARING A LITTLE WAYS THEN PUILL UP ON STRUT ASSEMBLY TO GET AXLE ALL THE WAY OUT OF BEARING/HUB ASSEMBLT. POP OUT AXLE ANT HE SLIDE IN THE NEW UNIT

Dec 30, 2010 | 1994 Hyundai Excel

1 Answer

How to replace CV joint


jack up vehicle, remove wheel, remove split pin from hub nut, remove nut, remove lower ball joint nut & separate ball joint, lever lower arm down, pull hub forward while pushing cv joint in wards through hub, remove cv gaiter clips and slide back on shaft, hold shaft firmly and knock cv joint off with hammer, pack new joint with grease, and place on shaft with nut on threads carefully knock on with hammer, re-fit parts in reverse order

Apr 24, 2010 | 1999 Hyundai Accent

3 Answers

Removing half shafts


if it not comes out and you do not want to destroy anything, look for the clamp inside. ( you can only see the ends, looking like I I )Clean the cv from grease, look from gearbox to wheelside around the shaft. in a small bay you can see a clamp, looking like two I I place a screwdriver or a needle nose plier in the middle and turn it to move the I I ´s apart. then you can easy pull the cv.

Mar 20, 2010 | 1993 Ford Escort 4 Door

1 Answer

Pulling drivers side half shaft on Toyota Camry 93 4 cyl


There is a pin in the differental that has to be taken out to pull the axles out. 1-bolt to remove the pin, then the C-clips will come off to slide the axles out.

Jan 08, 2009 | 1993 Toyota Camry V6

5 Answers

Cv joint


is it on the driver side or the passenger side? when i have a little trouble i use a slide hammer. put the nut on the shaft and use the 3 jaw attachment of a slide hammer this will help you.

Sep 01, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
1997 Toyota Camry Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...