Question about 2000 Pontiac Bonneville

1 Answer

Burned out fog light

Can't find access to back of assembly to replace burned out bulb.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You have to remove the plastic cover that is connected to the spoiler. It is the width of the car. After you remove it you can access the fog light. Hope this helps you.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

Directions on how to replace fog ligt bulbs on a 2008 elantra


  1. You may have to jack up the front end of the car to be able to slide under the vehicle a bit or if your arms are long enough you should be able to reach underneath the vehicle and feel for the connector.
  2. So now you see the connector simply give a turn counterclockwise and it will come loose.
  3. Now pull the bulb assembly out.
  4. The fog lamp will pull strait out of the connector.
  5. Replace with a new 9006 bulb.
  6. Now put the bulb assembly back in the fog light assembly.
  7. Turn the bulb assembly clockwise till it click's.
  8. Job completed.
ironfist109_15.gif
Regards, Tony

Apr 30, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

How do you replace the fog light bulb on 2008 avalanche


    • 1 Open the hood and reach down into the engine bay for the fog light assembly. If you cannot reach the fog light assembly from the top you may need to get underneath the truck to reach it. Remove the electrical plug running to the fog light ballast.
    • 2 Remove the bulb. Unlock the fog light bulb by turning it counterclockwise and pulling it straight out of the assembly.
    • 3 Slide a new bulb into the fog light assembly. The part number you will need for the new bulb will be located on the ballast or base of the old bulb.
    • 4 Turn the bulb clockwise to lock it into the fog light housing.
    • 5 Reconnect the electrical connector to the bulb ballast.

Jan 23, 2011 | 2007 Chevrolet Avalanche LTZ

1 Answer

Describe how to change fog lamp (just the bulb) on 2005 subaru forester. As far as I know the fog light assembly is fine, the bulb has just burned out. If you know which bulb to use please let me know,...


2005 Forester - It is easiest to remove the fog assembly.

1. From underneath the vehicle pry out one plastic fastener to be able to bend the light weight plastic mud protector downward. You will see the underside of the fog light assembly with one 10mm bolt directly above you. Remove this bolt.
2. From the front of the vehicle unscrew one 10mm bolt at top of fog light (this is the shorter of the 2 by the way) and pry out one plastic rivet adjacent to it.

3. Carefully remove the fog assembly and disconnect 2-pin power connector by pulling up on the release. Carefully wiggle the housing out (no force req'd).
4. Unscrew the back from the housing and replace H3 bulbs. Take care not to touch the bulb while replacing.

5. Reverse to install.

Should take an hour at most.

Dec 15, 2009 | 2005 Subaru Forester

1 Answer

How do I replace the fog light assembly on a 2000 Olds Alero?


you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.

Dec 03, 2009 | 1999 Oldsmobile Alero

1 Answer

Replace fog light bulb for 2006 Honda Odyssey


Touring Model
Use a wrench to remove the mounting bolt from the underbody through the hole in the splash shield.
Remove the fog light assembly from the bumper by pulling its inner edge first, then the whole assembly out of the bumper.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
Remove the bulb from the fog light assembly by turning it one quarter turn counterclockwise.
Push the electrical connector onto the new bulb.
Turn on the fog lights to test the new bulb.
Reinstall the fog light assembly into the bumper. Tighten the mounting bolt.
Insert the new bulb into the assembly and turn it one-quarter turn clockwise to lock it in place.
Hope this helps you.

Nov 22, 2009 | 2006 Honda Odyssey

2 Answers

Fog lights are burnt out i would like to replace them ??


Front Fog Light Assembly

REMOVAL

  1. Disconnect the ground cable from battery.

  • Remove the two clips and lower mudguard.
  • Disconnect the harness connector.
Remove the lower bolts.

  1. Remove the mounting bolts and clip, and then detach the fog light assembly.
INSTALLATION

Install in the reverse order of removal.
Front Fog Light Bulb

REMOVAL

  1. Remove the front fog light assembly.
Remove the back cover.

  1. Remove the spring retainer, and then detach the fog light bulb.
INSTALLATION

Install in the reverse order of removal.

Oct 03, 2009 | Subaru Forester Cars & Trucks

1 Answer

How do I replace fog lights on my 2002 Hyundai Santa Fe?


Look up into the bumper and see if you can access the fog light. The bulb should just twist out of the back. If not, the assembly should either pop forward or back to come out. I've heard though, that many santa fe's require the removal of the entire front bumper fascia just to get to the bulbs in which case you'd have to remove your headlights to get to the screws holding the bumper fascia on

Sep 09, 2009 | 2002 Hyundai Santa Fe

2 Answers

How to replace fog light bulbs


hi..You will have to access the fog light bulb from below the vehicle.
Remove the plastic clips from the wheel well cover extension that is
below the fog light.once the clips are out and the plastic cover is pull
down,you should be able to see the back of the fog light.you can try
to replace the fog light bulb by removing the two 10mm bolts and slide
the fog light assemble out through the front of the bumper.Turn the cover
of the rear of the fog light and replace light.
try this out..
thank u..
kindly rate my response..

Jun 14, 2009 | 2004 Toyota Celica

1 Answer

Replace the fog light bulb.


you don't. you disconnect the wire on the back of the light assembly and then the bulb twists counter clockwise and pops out, to re-install reverse the procedure. the wire is accessible from below the car under a black plastic flap the pulls down out of the way directly underneath the fog light.

Oct 26, 2008 | 2002 Buick Regal

Not finding what you are looking for?
2000 Pontiac Bonneville Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...