Question about 2005 Chevrolet TrailBlazer

1 Answer

Head light burned out

Driver side head light burned out low beam

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Just did 06 open hood look at top of light  should be 2 L shaped pins turn  and lift out whole light will lift out then change bulb no tools needed 06

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do all lights work except low beam driver side head lamp?


Seems like if your other low beam is lit, there's something wrong with the new bulb. Make sure it's the exact type needed, and switch the working bulb from the pass. side to drivers side to check.

Feb 22, 2016 | 2010 Nissan Altima

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

3 Answers

One low beam head lights will not work, high beam works though


check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

Dec 29, 2013 | 1997 Chevrolet Blazer

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

I put in a new headlight bulb in the drivers side in but i dont have low beams but high beams work what is the problem?


Usually the low beam light of the bulb burns out first, so this new bulb is acting like it is defective. If the passenger side bulb is working for both low and high beams you could test this new bulb on that side to be sure. If it works OK on this side there may be a problem with the connector wiring on the driver side.

Nov 24, 2013 | Cars & Trucks

1 Answer

2007 equinox head lights burn out all the lights go dim hit the casing and they go bright again changed the pig tales and it still does the same thing why ??


I have changed the head lights in are Equinox several times. They work great for some time I would say after 4 mouths 1 will burn out . The low beam. I will change both lights. again not touching the leans putting them in with a clean rag.work great then in about 3 mouths the other side low beam will burn out. Again taking both out. I bought the best you can buy lights put them in September. 1 day the 1 burned out the next day the other side burned out low beam. So on March 3,I put in 2 new one's. again crossing my fingers. I'm almost redy to go to the dealer on this one. any idea's. Need help with my 2007 Equinox in Pa. Thanks Roger

Feb 27, 2013 | 2007 Chevrolet Equinox

1 Answer

I have aproblem with my Buick Allure both low beam stoped working.The high beam works OK. Checked the fuses and there OK can you help


suspect low beam head light fuse, check fuse if ok suspect that both low beam head lights are burned out ( it happens) ,if ok suspect headlight dimmer switch.

Nov 16, 2010 | Chevrolet Avalanche Cars & Trucks

1 Answer

F 150 Head light issue


You know the fuse for the high beams is good ( Cab fuse panel fuse # 16 ) and the pass low beam fuse ( cab fuse panel # 26 ).
Might want to check cab fuse panel fuse #28 ( this is the driver's side low beam ).

If this fuse has power on both sides ( with the low beams on ) next you can pull the headlamps, and check for power at the connectors, but depending when the last bulb change took place, I would say you need need bulbs. ( need at least 1 for the high beam out )
Confirming with a meter at the headlamp would be a good idea, before spending the money.

The bulb connector has 3 pins.
Black wire is ground on both sides
Light Green w/ Black stripe wire is high beams on both sides
Driver Lo = Dark Blue w/ white stripe
Pass Lo = Dark Green w/ Orange stripe.


Nov 16, 2009 | 2002 Ford F150 Regular Cab

1 Answer

2004 BMW X3 driver side low beam headlight


remove the air filter housing ,simple .this programme has a spell check thingy working and its driving me nuts ,it cant identify plain english ,write colour and it squiggles it out but color is ok .

Oct 30, 2009 | 2004 BMW 3 Series

1 Answer

My passenger side low beam is dimmer then the drivers side


Check for a bad ground for that headlight.

Jan 16, 2009 | 1997 GMC Sierra

Not finding what you are looking for?
2005 Chevrolet TrailBlazer Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...