Question about 2004 Chevrolet Cavalier

1 Answer

WHERE IS THE THE FUEL PRESSURE REGULATOR AT?

WHERE IS THE FUEL PRESSURE REGULATOR AT?

Posted by on

  • hertle34 Jan 07, 2009

    ON MY 1999 CAVILER

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers

You have two different options. If you engine is a 2.2L, it will be located on the bottom side of the fuel rail. If your engine is at 2.4L, it will be located on the end of the fuel rail. I hope this helps you. Please leave a good rating.

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is location of fuel volume regulator


Fuel pressure regulator ! An it's location is inside the fuel tank .
The fuel pump (FP) module contains the fuel pump, fuel pressure regulator and the fuel sender assembly. The fuel pressure regulator is attached to the fuel pump in the fuel pump module located in the fuel tank. It regulates fuel pressure supplied to the fuel injectors. The fuel pressure regulator is a diaphragm-operated relief valve. Fuel pressure is established by a spring preload applied to the diaphragm. Excess fuel is bypassed through the regulator and returned to the fuel tank.

Nov 18, 2015 | 2002 Ford Explorer

1 Answer

Im gonna rplace the fuel pressure regulator. In the haynes manuel it says that you need to remove the fuel rail. Ive asked a few people and they said they dont think it is necassary it is an 03 impala. ...


Not sure why Haynes says to do that. below is instructions from autozone.com, and none of the engines require the fuel rail to come off. That said, if you have the 3.4, you may need to pull the upper intake manifold.


Removal & Installation The need to work as cleanly as possible cannot be over-emphasized. Even the smallest amount of dirt, if allowed into the fuel pressure regulator and/or the fuel rail, will find its way to the fuel injectors. The nozzle openings of the injectors are very small. Keep hands and tools clean. Clean the areas to be disconnected with a suitable solvent. Carefully cover open fittings and connections to keep out foreign material. Dirt in the injectors almost guarantees a clogged fuel injector and engine performance problems.

3.4L (VIN E) Engines

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Remove the upper intake manifold assembly.
  4. Disconnect the vacuum line from the pressure regulator.
  5. Remove the regulator retaining screw and remove the retainer bracket. Using a clean shop cloth to catch fuel spillage, carefully pull the regulator from the fuel rail. Twist the regulator slightly while removing to ease removal. Discard the O-ring.

    0996b43f802307fd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the fuel pressure regulator mounting-3.4L (VIN E) engines


To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate a new pressure regulator O-ring with clean engine oil and install on the regulator inlet.
  4. Install the fuel return pipe to the regulator.
  5. Install a new retainer and spacer bracket into the slot on the fuel rail and install the pressure regulator to the fuel rail. Tighten the fuel return line nut to 13 ft. lbs. (17 Nm).
  6. Connect the vacuum line to the pressure regulator and install the retainer screw. Tighten to 76 inch lbs. (8.5 Nm).
  7. Inspect and verify that the retainer and spacer bracket is engaged in the slots in the fuel rail. Grasp and pull on the regulator to ensure that it is properly seated.
  8. Install the upper intake manifold.
  9. Connect the negative battery cable.
  10. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

3.8L Engines
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Clean any dirt from the fuel pressure regulator retaining ring.
  4. Remove the vacuum hose from the pressure regulator.
  5. Remove the snaprings. Twist the regulator slightly and pull the pressure regulator from the fuel rail. Use a shop towel to catch fuel spillage as the regulator is removed.
  6. Remove the O-rings and O-ring back-up.

To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate the new pressure regulator O-rings with clean engine oil. Install the O-ring back-up, the large O-ring and then the small O-ring. Install the pressure regulator and secure with the snapring.
  4. Attach the vacuum hose.
  5. Connect the negative battery cable.
  6. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Clean any dirt from the fuel pressure regulator retaining ring.
  4. Remove the vacuum hose from the pressure regulator.
  5. Remove the snaprings. Twist the regulator slightly and pull the pressure regulator from the fuel rail. Use a shop towel to catch fuel spillage as the regulator is removed.
  6. Remove the O-rings and O-ring back-up.

To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate the new pressure regulator O-rings with clean engine oil. Install the O-ring back-up, the large O-ring and then the small O-ring. Install the pressure regulator and secure with the snapring.
  4. Attach the vacuum hose.
  5. Connect the negative battery cable.
  6. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

Mar 16, 2011 | 2003 Chevrolet Impala

1 Answer

I need to replace de fuel presurre sensor in a pontiac montana ,do i have to just replace the sensor ,o the sensor came with the fuel pump?thank you


Replacing the fuel pressure regulator, involves just replacing the regulator at the end of the fuel rail in the engine compartment, but fuel pressure sensor - does this mini-van have a fuel pressure sensor?
replacing the fuel pressure regulator: (1) locate it at the end of the fuel rail in the engine compartment,
(2) relieve fuel system pressure (3) disconnect fuel pressure regulator vacuum line. (4) remove fuel pressure regulator retaining screw (retain for re-use (5) using a shop towel to catch spilled fuel, lift & twist Fuel pressure regulator to remove it from the fuel rail. (6) remove/discard retainer and spacer bracket from the fuel rail. (7) remove fuel pressure regulator from the engine fuel return pipe. (8) remove/discard Fuel Pressure Regulator inlet O-ring (9) Check Fuel Pressure Regulator filter screen for contamination - if contaminated, replace Fuel Pressure Regulator. (10) Lubricate new Fuel Pressure Regulator inlet O-ring with clean engine oil & install onto the Fuel Pressure Regulator inlet. (11) Install the fuel return pipe onto the Fuel Pressure regulator (12) Install new retainer & spacer bracket into the slot on the fuel rail.
(13) Install Fuel Pressure Regulator onto Fuel Rail & tighten Engine Fuel Return Pipe nut to 13 ft-lbs (17 Nm). (14) connect Fuel Pressure Regulator vacuum line, (15) Install Fuel Pressure Regulator attachng screw & tighten to 76 in-lbs (8.5 Nm). (16) Inspect & verify that retainer & spacer bracket is engaged in the slots on the fuel rail. Grasp & pull on the Fuel Pressure Regulator.
to ensure that the Fuel Pressure Regulator is properly seated. (17) inspect for fuel leaks with this
procedure: On 2sec,(holy rollers), off 10sec will be left on, inspect for leaks while running.

Dec 11, 2010 | 2000 Pontiac Montana

1 Answer

Overreving with no power and excessive gas consumption air filter cleaned map sensor replaced fuel pump and filter


usually caused by busted diaphram in fuel pressure regulator allowing fuel to be drawn thru regulator directly to intake manifold. Pull vacuum line off regulator, plug line with golf tee, start car and watch to see if gas comes out of regulator. If yes, turn off car, replace regulator. The regulator sits near the fuel rail on the top of the engine as shown below. I will paste replacement instructions below from autozone.com in case you need to replace the regulator. Please let me know if you have any questions.
jturcotte_421.gif


Removal & Installation

4.2L Engine

  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.

To install:
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.

  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.

Dec 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

If i put a little gas in the carberator and fight with my blazer it will start and stay started, but if i leave it for awhile, it will turn over but not start. i cant figure out if it is electric or...


Get a fuel pressure gauge and connect it to the rail for the fuel injectors to read pressure.

If the pressure is too low, it might be a bad fuel pressure regulator or pump:

Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Nov 04, 2010 | 2002 Chevrolet Blazer

1 Answer

I have a 2004 Tahoe which has misfire problems (P0300). I changed the plugs, wires, fuel filter and air filter but problem still exist. The 4 plugs on the passenger side continue to file out and become...


Removal & Installation of fuel Regulators on
4.8L, 5.3L & 6.0L Engine To Remove:
CAUTION
Three styles of fuel pressure regulators and fuel rails will be used in this model year. Each regulator has a different "footprint" that consequently changes the size of the receiving port in the fuel rail. The regulator retaining clips are specific to each rail-regulator design and cannot be interchanged.
chevy_aval15_02-04_fuelrail.gif

  1. Remove the engine sight shield.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  3. Clean the fuel pressure regulator retainer and the surrounding area.
  4. Remove or disconnect the following:
    • Fuel pressure regulator vacuum line.
    • Fuel pressure regulator retainer.
    • Fuel pressure regulator.
  5. Remove the following parts from the fuel rail:
    • Backup ring (10)
    • Regulator Seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
To Install:
chevy_aval15_02-04_retainer.gif

  1. Make sure the NEW fuel pressure regulator retainer is the right one.
  2. The tabs (1) are used on the straight vacuum port retainer (2), and the E85-straight vacuum port retainer (3).
  3. The angle vacuum port retainer (4) has no tabs. chevy_aval15_02-04_fuelrail.gif

  4. Install the following parts onto the fuel pressure regulator (9).
    • Backup ring (10)
    • Regulator seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
  5. Lubricate the fuel pressure regulator O-rings with clean oil.
  6. Install the fuel pressure regulator and retainer. CAUTION
    Whenever the fuel pressure regulator is removed from the fuel rail NEW O-rings and a NEW retaining clip should be used on reinstallation.
  7. Connect the vacuum line.
  8. Tighten the fuel filler cap.
  9. Use the following to inspect for leaks:
    • Turn ON the ignition, with the engine OFF, for 2 seconds.
    • Turn OFF the ignition for 10 seconds.
    • Turn ON the ignition, with the engine OFF.
    • Install the engine sight shield.
8.1L Engine To Remove:
Fuel pressure regulator vacuum line gm_trk_sub15_fuel_press_reg_vac_line.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of thjs section
  2. Remove the fuel injector sight shield as needed
  3. Relieve fuel system pressure (See: Fuel Pressure Relieving)
  4. Disconnect the fuel pressure regulator vacuum line (A) 8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  5. Clean any dirt from the fuel pressure regulator retainer and the surrounding area
  6. Remove the fuel pressure regulator retainer (I)
  7. Remove the fuel pressure regulator (H) from the fuel pressure regulator housing
To Install:
8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  1. Install or connect the following:
    • Backup ring (J) on the fuel pressure regulator (H)
    • New large O-Ring (K) on the fuel pressure regulator
    • Regulator filter (L) on the fuel pressure regulator
    • New small O-Ring (M) on the fuel pressure regulator
  2. Lubricate the fuel pressure regulator large O-Ring and the small O-Ring with clean engine oil
  3. Push the fuel pressure regulator onto the regulator housing on the fuel rail
  4. Install a new fuel pressure regulator retainer (I)
  5. Install or connect the following:
    • Fuel pressure regulator vacuum line
    • Negative battery cable
  6. Tighten the fuel filler cap
  7. Inspect for leaks using the following procedure:
    • Turn on the ignition with the engine off for two seconds
    • Turn off the ignition for 10 seconds
    • Turn on the ignition with the engine off
    • Inspect for fuel leaks
  8. Install the fuel injector sight shield
  9. Road test the vehicle to check performance
prev.gif next.gif

Sep 02, 2010 | Chevrolet Tahoe Cars & Trucks

2 Answers

Have 1998 safari 4.6 throttle body cannot find fuel pressure regulator


Astro, Safari 1997-2005

Fuel Pressure Regulator - Removal & Installation
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure. Refer to the fuel system relief procedure in this section.
  3. Remove the upper manifold assembly.
  4. Remove the fuel pressure regulator vacuum tube.
  5. Disassemble the fuel pressure regulator snapring retainer.
  6. Remove the fuel pressure regulator assembly and the O-rings. Discard the O-rings, filter and back-up O-rings.

    5d30462.jpg
    Fig. The fuel pressure regulator is retained by this clip


    913de3d.jpg
    Fig. Replace the O-rings whenever the fuel pressure regulator is removed
To install:
  1. Lubricate the O-rings with clean engine oil and install as an assembly.
  2. Install the fuel pressure regulator, attach the vacuum tube.
  3. Install the snapring retainer.
  4. Install the upper manifold assembly.
  5. Connect the negative battery cable.

  1. Relieve the fuel system pressure.
  2. Remove the upper intake manifold assembly.
  3. Remove the fuel pressure regulator retainer clip (5).
  4. Pull and twist the fuel pressure regulator (6) in order to remove the fuel pressure regulator from the fuel pressure regulator housing using a shop towel to catch any spilled fuel.
  5. Remove the regulator seal lower O-ring (3).
  6. Remove the regulator assembly filter (2).
  7. Remove the regulator seal upper O-ring (1).
  8. Remove the regulator seal backup ring (7).
  9. Discard the O-rings.

    a29bed6.jpg
    Fig. Exploded view of throttle body assembly (click for zoom)
To install:

NOTE If the fuel pressure regulator is to be reinstalled, inspect the filter screen for contamination. If the filter screen is contaminated, replace the regulator.
  1. Lubricate the new O-rings with clean engine oil.
  2. Install the regulator seal backup ring (7).
  3. Install the regulator seal upper O-ring (1).
  4. Install the regulator assembly filter (2).
  5. Install the regulator seal lower O-ring (3).
  6. Assemble the regulator (6) with the vacuum tube pointing down into the regulator retainer clip.
  7. Install the fuel pressure regulator retainer clip (5).
  8. Install the upper manifold assembly.
  9. Connect the negative battery cable.
  10. Inspect for leaks.
    1. Turn the ignition ON , with the engine OFF , for 2 seconds.
    2. Turn the ignition OFF for 10 seconds.
    3. Turn the ignition ON , with the engine OFF .
    4. Inspect for fuel leaks.
  11. Install the engine cover.

Hope helps with this (remember comment and rated this).

Aug 05, 2010 | GMC Safari Cars & Trucks

2 Answers

Locating fuel pressure regulator


Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 05, 2010 | 2001 Chevrolet Blazer

1 Answer

Where is fuel pressure regulatore located


For 2000 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl
If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold.

The throttle body is mounted on it and your fuel lines terminate into the center of this.


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.
To install:


aaf5240.jpg
Fig. Fuel pressure regulator-4.2L engine
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.
Hope help with this (remember rated this post).

Feb 26, 2010 | 2000 Chevrolet Blazer

1 Answer

How to change a fuel pressure regulator in a 1997 pontiac grand prix


GM Century/Lumina/Grand Prix/Intrigue 1997-2000
Fuel Pressure Regulator - Removal & Installing

The fuel pressure regulator is a diaphragm-operated relief valve with fuel pump pressure on one side and regulator spring pressure and intake manifold vacuum on the other side. The regulator's function is to maintain a constant fuel pressure across the injectors at all times. The pressure regulator compensates for engine load by increasing fuel pressure as engine vacuum drops.

The fuel pressure regulator is serviced as a separate component. When servicing the pressure regulator, make sure that the O-ring back-up, large O-ring, filter screen and small O-ring are properly positioned on the pressure regulator.


44dcbf8.jpg Fig. Cutaway view of a typical fuel pressure regulator


REMOVAL & INSTALLATION
The need to work as cleanly as possible cannot be over-emphasized. Even the smallest amount of dirt, if allowed into the fuel pressure regulator and/or the fuel rail, will find its way to the fuel injectors. The nozzle openings of the injectors are very small. Keep hands and tools clean. Clean the areas to be disconnected with a suitable solvent. Carefully cover open fittings and connections to keep out foreign material. Dirt in the injectors almost guarantees a clogged fuel injector and engine performance problems.
3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure using the procedures found in this section.
  3. Remove the upper intake manifold assembly. Please see .
  4. Disconnect the vacuum line from the pressure regulator.
  5. Remove the regulator retaining screw and remove the retainer bracket. Using a clean shop cloth to catch fuel spillage, carefully pull the regulator from the fuel rail. Twist the regulator slightly while removing to ease removal. Discard the O-ring.

4ecb713.jpg

Fig. Exploded view of the fuel pressure regulator mounting-3.1L and 3.4L (VIN E) engines
To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate a new pressure regulator O-ring with clean engine oil and install on the regulator inlet.
  4. Install the fuel return pipe to the regulator.
  5. Install a new retainer and spacer bracket into the slot on the fuel rail and install the pressure regulator to the fuel rail. Tighten the fuel return line nut to 13 ft. lbs. (17 Nm).
  6. Connect the vacuum line to the pressure regulator and install the retainer screw. Tighten to 76 inch lbs. (8.5 Nm).
  7. Inspect and verify that the retainer and spacer bracket is engaged in the slots in the fuel rail. Grasp and pull on the regulator to ensure that it is properly seated.
  8. Install the upper intake manifold. Please see .
  9. Connect the negative battery cable.
  10. Inspect for leaks using the following procedure:
    • Turn the ignition switch to the ON position for 2 seconds.
    • Turn the ignition switch to the OFF position for 10 seconds.
    • Turn the ignition switch to the ON position again.
    • Inspect all areas for fuel leaks.

Other size engine can find in autozone.com (free register).

Hope this help (remember rated this).

Feb 08, 2010 | 1997 Pontiac Grand Prix

Not finding what you are looking for?
2004 Chevrolet Cavalier Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...