Question about 1998 Isuzu Rodeo

1 Answer

98 rodeo jumps out of four high

Does not jump out of 2x4 or4x4 low

Posted by on

  • yadayada
    yadayada May 11, 2010

    rebuild the transfer case

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Sounds like the cable or silinoid needs to be adjusted.

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of 4 wheel drive relay on 98 ford ranger


All the relays are under the hood on these rangers, but you problem may be with the control box behind the jump seat on the drivers side. You may have to remove the jump seat to get to it. Once there, the box will have a white,grey or black button on it. Usually on the end where the red light is, Turn the key on and press this button and hold for 5 seconds. This puts the 4 wheel drive shift motor back in sequence. Now without starting the engine and the trans in park if auto and neutral if standard park break set, try the to shift in to 4 high, if you can hear the shift motor run and shift the gears in the transfer case, try 4 low, you should hear the same motion in the transfer case, if so you have solved your problem. If not you may have to move on to the connector on the transfer case, you may have to unplug the connector and look at the pins and socket, if they look corroded, clean and apply some dielectric grease to the pins and the socket and plug back in. Try the 4 High and 4 low again. If it works, great, if not you may have a bad shift motor.
Good luck.


Feb 25, 2014 | 1998 Ford Ranger

1 Answer

Climate control fan stays on after jump start, cycling from low to high


Blower motor resister is bad.Easy to remove,it's located by blower motor,click here to see what it looks like.

Jan 17, 2013 | 1998 Nissan Maxima

1 Answer

89/98 olds. regency. its runs for awhile and then shuts off. it also backfires through the exhaust at high rpms


Probably timing. Aim a timing light at your crankshaft, and see if the mark is jumping back and forth irradically. It should be staying in one spot. If it's jumping around, your timing chain has jumped a cog.
If not the timing, then it's probably bad wires or improper firing order .

Jan 11, 2012 | 1989 Oldsmobile Ninety Eight

1 Answer

I have a 2006 isuzu rodeo and i cant get it out of four wheel drive low i have try to put it in 2 wheel drive high and four wheel drive high but it still coomes up on dash that its four wheel drive low...


I have 2002 and I find that you have to come to a complete stop, put it in reverse momentarily, and that should take care of it. Cheaper than going to the dealer and having them really fix it!!!

Oct 02, 2011 | 2004 Isuzu Rodeo

1 Answer

1994 nissan pathfinder- when I push in the clutch it will let me shift through the gear but does do anything - when I depress the interlock put in 1st gear it jumps into four wheel drive - tranny and...


ipresume your talking about a manual gearbox
and you have a seperate lever for four high and four low possibly 2 wheel drive on it as well trouble has to be in smalllever linkage and not engaging properly to solve it move the lever around different positions see do u get drive

Mar 06, 2010 | 1994 Nissan Pathfinder

2 Answers

1996 lincoln towncar. No a/c compressor engagement unless jumped


the control unit is no good.i had a similar situation with a 98 tracker,and installed a switch to give it a ground for the compressor relay that comes from the a/c computer module.
it works good and goes on and off with the a/c switch.

Jul 18, 2009 | Lincoln Town Car Cars & Trucks

1 Answer

Jumping problem


fuel filter maybe?

Apr 16, 2009 | 1999 Isuzu Rodeo

1 Answer

Stalls won't start even wtih jump


just a few easy things to check! if your battery is more then 3 yrs old,its a good idea to replace it, even if this is not the cure, but it sounds to me it is a good possibility,had the same problem with my car! see you don't want to jump start it through the battery in your car! the way to buy pass a bad battery is to connect the positive cable from the good battery to the positive post on the car being jumped, connect the negative cable to the frame of the car being jumped,NOT TO THE BATTERY.also, when u get it running take it right to a place that can check your alternator to make sure its o.k. their are some auto part stores that will do that for free and u could get the battery from them if needed.good luck to u,hope we helped!

Feb 28, 2009 | 1998 Isuzu Rodeo

1 Answer

4-wheel high problem


reset the 4x4 computer by pulling out the courtesy lamp fuse and the ATC fuse for 1 minute then reinstall both fuses then cycle the key on and off 5 times. if this works please rate.

Nov 17, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...