Question about 1986 Nissan Stanza

1 Answer

Where is the fuel filter on a 1986 Nissan Stanza Wagon?

Posted by on

  • yadayada
    yadayada May 11, 2010

    check the engine compartment on the fire wall.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

Most cars fuel filter is under car.

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 stanza... Went to startit. It


you have low fuel consumption

Oct 23, 2012 | 1986 Nissan Stanza

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

I need rear struts for a 1986 Nissan Stanza wagon 4x, anyone know where I can purchase these?


Did you think to look in the yellow pages under " auto parts" ? Is this a real question? WTF?

Sep 09, 2010 | 1986 Nissan Stanza

1 Answer

Where are the fuel filter and 02 sensors located on a 1987 nissan stanza?


I don't know if are cars are built alike. I have a 1990 stanza and the fuel filter is located under the hood on the firewall to the left of the brake booster. Oxygen sensors would be in the exhaust manifold.

Jul 16, 2009 | 1991 Nissan Stanza

1 Answer

92 Nissan Stanza sputtering and stall


You may have frozen fuel lines. Sounds like not enough fuel is getting to the engine. You may need to bleed the system and change fuel pump, fuel filter and check the injectors

Jun 19, 2009 | 1990 Nissan Stanza

1 Answer

I need the number on the computer (ECU) nissan Stanza 87 SW, STD,FWD


Hi... On your question For ECM to 1987 Nissan Stanza..
Are 6 Available number .
2 are for vehicles 4WD. Incl. wagon. Calif emissions. 2261A-20R66RE,
with out calif, 2261A-20R06RE,

2 For vehicles FWD Wagons only. Calif emissions, 2261A-20R75RE,
With out Calif emissions, 2261A-20R15RE.

2 For vehicles Sedans FWD Exc Wagon. Calif emissions, 2261A-D5507RE,
With out calif emissions, 2261A-D4507RE,

NOTE , " RE" Mean Remanufactured ECM. Is not available new.

Ok.. Are the number I have Based on Mitchell ondemand, Repair Software.

I hope this info help on your question.
Any more questions let me know...


Nov 07, 2008 | 1987 Nissan Stanza

1 Answer

Gears


Could be the clutch is wearing down.If it's in ALL gears,it is likely the clutch.If i remember correctly,your car has a hydraulically activated clutch.If this is the case,under the dash,where the clutch pedal attaches to the clutch master cylinder,there is a jam nut,either 12mm or 14 mm wrench,loosen the jamnut,and spin the threded rod in,towards the clutch pedal,and away from the firewall.This should make your clutch pedal engagement point closer to the floor,and easier to shift.

Jul 08, 2008 | 1986 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...