Question about 2001 Ford Windstar

1 Answer

Heater problem how the blend door actuator look like? and where it is located? any body have the picture?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

HAVE PART NUMBER F2Z19E616FB SEE PICTURE AT DORMAN.COM # 604203

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the a.c. heater blend door actuator located on a 2005 crown victoria


images for Where is the a.c. heater blend door ...

Fix Heat Door Actuator. - YouTube

? 6:17
https://www.youtube.com/watch?v=NkUPsacbYzc
Oct 7, 2012 - Uploaded by zephmont
My 2005 Crown Vic is blowing out a little heat at times but not how it normally does. .... actuator to press the ...

2003 ford crown vic Heat blender actuator fix - YouTube




Nov 26, 2015 | Cars & Trucks

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

Heater blows hot on drivers side cold on passenger side


it depends on what model and what options your Journey is equipped with. if it has a dual zone control climate control, it sounds like the blending actuators are not aligning properly or the blend doors are not adjusting to cooperate with the main climate control system. the temp. of the vehicle is controlled by Blend doors in the h/vac system that is thereby controlled by the body control module of the vehicle. the module is a computer that controls all functions within the body of the vehicle. the module should have problem codes that should isolate the area that needs attention.
the body module controls the blend doors in the h/vac system, the doors that open and close in the vents by the heater core that controls the temperature that is ultimately expelled the correct temperature that comes out of the vents. if the settings on both the drivers and passengers control knobs for example are on cold, and one side is hot and one side is cold, then there is a problem at the module level or most likely the blend door is the problem. most likely the actuator ( the motor that runs the blend door and controlled by the module) is not operating properly. your dealer will hook the module up to a diagnostic computer and retrieve the codes ( if any) and isolate which blend door is not working correctly.

usually its just a blend door actuator that needs replacing. to rule out heater core issues, if there is no excessive condensation on the windows and coolant on the carpet, then most like it's a module or blend door issue. if it's a single mode climate control, the same is true but puzzling b/c in that case, both passenger and driver h/vac system is designed to push out a consistent temp for both side without the option of variation on either side. again most likely a blend door issue.

hope this helps

Mar 04, 2014 | 2009 Dodge Journey

2 Answers

HVAC heater blend door actuator is not working


check HVAC fuse.if fuse okay heater control module could be the problem.

Nov 19, 2013 | Hyundai Cars & Trucks

1 Answer

Blend door actuator failed ,how do i fix it?


The temperature blend door actuator itself is not repairable....it will have to be replaced. Its located under the center dash and is screwed to the heater box. I have included a picture of what it looks like.
2_14_2013_2_40_25_pm.jpg

Feb 14, 2013 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Where is the blend door actuator located


The blend door is on the heater box, you will neeed to turn heater on with low air setting as you look around box to locate it, it is hard to say exactly where it is on the box due to its been a while since i replaced one, let me see if i can get a diagram. this is a 1999 ford taurus.

Okay the actuator on this car is located on the box on the passenger side, if you look from passenger side toward center of the dash you will see it bolted to box below radio area, you may need to remove the lower dash covers. here is a picture to help you.10_24_2012_11_35_10_am.gif

Oct 24, 2012 | 1999 Ford Taurus

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

1 Answer

Afternnon, just wondering about the best way to locate the blend doors in the hvac box without ripping out the dash on my 2000 jeep grand cherokee. Thanks in advance. Duane


y9ou can gain access to the driver side blend door actuator by removing the glove box. The actuator will be in the left corner of the glove box opening. If you remove the actuator you will be able to turn the pin. If you can turn it 360 degrees the blend door is broke.

If your lucky its only the drivers side. If you get the repair kit from chrysler it will come with instructions with pictures on how to replace the blend door without pulling the HVAC unit/Dash. If the passenger side is broken the HVAC unit will need to be removed.

Heater treater (google them) also have a metal blend door replacement and instructions online on how to replace them without pulling the HVAC housing.

Nov 28, 2010 | 1999 Jeep Grand Cherokee

2 Answers

I have no heat. the blower works but no heat coming out? the guy i just bought it off of said he just replaced the heater core??? help?


check to see if both heater hoses goto heater core is hot, if they are then you have a blend door actuator problem
if one hose is hot and the other is colder then you have air pocket in the system.

Feb 28, 2010 | 2005 GMC Canyon

1 Answer

No heat Heater core is hot


If heater core is getting coolant circulating through it then you may have a temp blend door, or blend door actuator not working properly. The blend door is located in the air box under the dash, and the actuator is located on the air box. You may be able to visually check the operation while turning the temp knob, by locating the coresponding actuator on the air box and monitoring the movement. If it is moving ok and still no heat then the blend door, or lever is broken, which will require removal of the dash.

Oct 17, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
2001 Ford Windstar Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...