Question about 2002 Chrysler PT Cruiser

1 Answer

Where is the crankshaft sensor on a 2002 pt crusier

Im getting code 0320 and car is stalling at various times but starts up or sometimes powers up on it own while driving.

Posted by on

  • Anonymous Mar 28, 2014

    lost key with chip tried to start with spare key. would't start. found my key with chip .now car won't even turn over

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

where is the crankshaft sensor on a 2002 pt crusie - 0eda6e7.jpg

Looks like its above the axel on the engine side . above oil filter . you should be able to find it from there , best picture i could find .

Posted on Jan 06, 2009

  • Rick Byrd
    Rick Byrd Jan 06, 2009

    just in case , you are viewing under vehicle , notice oil filter and drain plug on oil pan . sensor bolting into block , just above oil pan .

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 PT CRUSIER SHUT OFF WHEN DRIVING


hi,

this normally happens when you have a bad crankshaft sensor or a bad harness, will recommend you to inspect your harness first if this looks ok, then have your crankshaft sensor replaced, this is located on the rear of the engine so have to raise the car and from the bottom you will see a 3 wire connector.
download-lblmtgsbf2txf1xztvvfpasw-5-0.png

Oct 13, 2017 | 2002 Chrysler PT Cruiser

1 Answer

2002 jeep grand cherokee diagnostic trouble code P 0320? how do i repair?


No Crank Reference Signal at PCM No reference signal (crank-shaft position sensor) detected during engine cranking. Use this youtube step-by-step to fix it. How to diagnose P0320 crankshaft position sensor circuit failure

May 01, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Have a 2002 chrysler pt crusier having running issues while driving


You probably need the egr valve changed or the passages beneath it cleaned of carbon deposits that are blocking up the passage of exhaust gas back into the engine. It's an important emission control device that reduces pollution by lowering combustion temperatures. When they get plugged up, it can cause stalling, so I would have it serviced.

Mar 22, 2013 | 2002 Chrysler PT Cruiser

1 Answer

I get a code 0340 on my 05 PT Crusier. Just started running real bad. step on gas and wants to stall like not getting gas. Can you help? Rc


p0340 is camshaft position sensor A-bank 1 curcuit malfunction, Its very likely you need a new cam sensor. check wiring also, the cam sensor is not expensive.

Apr 20, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Changed the timing belt and camshaft sensor on a 2005 pt crusier pretty sure its timed correctly because the car seems to run fine and revs high with no problems although it still throws P0016 code even...


What the P0016 code means. P0016 is the OBD-II generic code indicating that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor. The camshaft timing is out of position due to the timing chain jumped teeth. The camshaft phaser is out of position due to problems with phaser.

May 22, 2017 | 2005 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Replace crankshaft sensor


Crank sensor on that car should be located near the pulley end of the motor, and near the firewall side. Fairly easy to get to.

Mar 06, 2009 | 2003 Chrysler PT Cruiser

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

Related Topics:

1,838 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...