Question about 1984 Chevrolet K1500

1 Answer

How to remove auto hubs on 84 4wheel drive pu

Need help removing auto hubs on a 84 1/2 ton 4wheel drive pu

Posted by on

  • cadiken Feb 04, 2009

    I need a Picture Brake down because the jamb nuts keep coming lose

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

There should be 5 or 6 allen bolts around hub. remove these and cover will come off then there is a snap ring on axle and one around the edge of hub remove thes and will slide off

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the easiest way to remove the rear hub on a 2005 Ford Explorer?


you need a hub wrench where the drive tangs engage the four slots in the hub nut and remove the nut.go to auto parts stores they carry hub wrench you also need 3 jaw puller loosen the rear hub to point of removal.

Nov 16, 2011 | 1999 Ford Expedition

1 Answer

Do i have to remove the differential housing cover to remove C - clips or can i just unbolt the hubs and remove both lock nuts on the hub because I want to check my rear brakes on a 65 chevy 3/4 ton...


Hi! sensenicht
Are there bolts on the outer hubs. If so removing the axel hub bolts will allow you to pull the axles. You should be able to remove the lock nut, lock washer and adjusting nut (second nut) to remove rear brake hubs and drums. The C-Clips are only used on the half ton and lighter cars. This is called floating axels.
Its important to replace the hub seals on the inside of the drums. A small amount of axel greese will make your brakes not work properly.
InMrFixIt

Jun 25, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

Cannot see how the hub is removed. The main nut on the end of the drive shaft has been removed butusing a bearing puller simply pushes the drive shaft back and does not remove the hub


You will need to remove the spindal assembly from the car and press the hub out with a 20 ton or larger press.You can try using a slide hammer puller but this is rarely sucessful.

Feb 20, 2011 | Volkswagen GTI Cars & Trucks

1 Answer

I have a '97 Chevy 1/2 ton 4x4 PU. Very good


Sounds like a loose connection, Clean the fuse contacts. Sometimes lubricant and dirt gets on the contacts within the switch itself and this will interfere with power supply. Have you checked the wiper relay corrosion and wear on the relay contacts impair electrical connection. Brighten up contacts with fine sand paper and if the relay contacts are suspect, remove the cover and draw folded sand paper between the contacts until clean.

May 13, 2010 | 1994 Lincoln Town Car

1 Answer

My truck will not lock into 4 wheel drive


sometimes need to remove hub and clean grease out and lightly regrease. or may need to replace hubs

Mar 11, 2010 | 1978 Chevrolet C1500

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

2 Answers

Bad front wheelbearing 2006 gmc sierra 1/2 ton pickup


Not too bad. Just break down the Hub and pull it out. You might need a big socket. Go get a chilton's manual, it will help you if you don't understand it.

Mar 26, 2009 | 2006 GMC Sierra

2 Answers

84 chevy 4 wheel drive auto hub removial


Remove the cap,look close and you vill see a snap ring inside the ¨pipe¨ take out the ring and then you should be able to pull out the hub.

Jan 06, 2009 | 1984 Chevrolet K1500

1 Answer

Remove the front disc rotor


The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...