Question about 1998 Nissan Altima

1 Answer

How do I remove a starter off a 1998 nissan Altima?

How do i take the starter off a 1998 nissan altima?

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

Need an engine size

Posted on Jan 29, 2009

3 Suggested Answers

ZJLimited
  • 17970 Answers

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Posted on Apr 05, 2010

volvo2103
  • 122 Answers

SOURCE: replacing a nissan altima sunroof

it should....same body style....

Posted on Feb 03, 2009

ilragatzzo78
  • 241 Answers

SOURCE: Replacing a starter for a 1999 Altima

  1. Disconnect battery ground cable.
  2. Disconnect starter wiring from starter.
  3. Remove starter retaining bolts and the starter.
  4. Reverse procedure to install.
the bolts should be on the drivers side.
you will have to crawl underneath the car to do this task

Posted on May 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 2002 starter to a Nissan Altima fit on a 1997 Nissan Altima


Nissan Altima was given a redesign.Furthermore, they are guaranteed to fit well on your Nissan Altima.

More information please visit this link:-- Nissan Altima

May 29, 2016 | Nissan Cars & Trucks

1 Answer

Howm do I replace a starter on a 1995 Nissan


Nissan 240SX/Altima 1993-1998 Repair Guide

Altima
(see Figures 1, 2 and 3)


ef972ea.jpg
Fig. 1: The starter is located to the left of the oil filter housing on the engine block


dfca7b3.jpg
Fig. 2: The starter motor is removed from the bottom side of the engine compartment


04c206e.jpg
Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the starter support bracket, as required.
  4. Label and disconnect the starter electrical harness.
  5. Support the starter from beneath the vehicle using a jackstand.
  6. Remove the starter mounting bolts.
  7. Carefully lower the starter from the vehicle.
To install:
  1. Position the starter on the engine and support it using a jackstand.
  2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
  3. Connect the starter electrical harness.
  4. Install the starter support bracket, as required.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 27, 2009 | 1995 Nissan Altima

1 Answer

Replacing a nissan altima sunroof


it should....same body style....

Feb 03, 2009 | 1998 Nissan Altima

1 Answer

How do you access bolts to starter ?


You'll need to block the rear tires and jack the car front end up on a hard surface and set it on jack stands. Then you get to crawl under the vehicle.

Jan 26, 2009 | 1998 Nissan Altima

1 Answer

Nissan Altima not starting(sometimes)


change your crank angle sensor and it should fix your problem

Jan 14, 2009 | 1998 Nissan Altima

1 Answer

1998 Nissan Altima


If the starter/solenoid is new/replaced, most likely the cable from the battery to the solenoid needs replacing or the connection ends saned and cleaned for a good electrical contact, Also chek the gound wire connections (if any)

Aug 23, 2008 | 1998 Nissan Altima

1 Answer

Nissan Altima 98


The starter solenoid (must buy complete starter) -or-
The cable from the battery to the solenoid needs replacing or the connections need cleaning
If you are handy, the starter can be rmoved without too much work and exchanged for a rebuilt/remanufactured one

Aug 23, 2008 | 1998 Nissan Altima

1 Answer

1998 Nissian Altima Not starting


Nothing by either party was said about the starter. The battery and wires can all be in great shape, and if they are and the owner hears a clicking noise when trying to start it its a pretty good bet they may have a starter that's locked up.


One good 'ole trick on those starters. If you can reach the starter, a couple of sharp rapes with a hammer will have it starting again, then you know it time to replace the starter.
Bill

Aug 23, 2008 | 1998 Nissan Altima

1 Answer

Replacing a starter for a 1999 Altima


  1. Disconnect battery ground cable.
  2. Disconnect starter wiring from starter.
  3. Remove starter retaining bolts and the starter.
  4. Reverse procedure to install.
the bolts should be on the drivers side.
you will have to crawl underneath the car to do this task

May 15, 2008 | 1999 Nissan Altima

Not finding what you are looking for?
1998 Nissan Altima Logo

Related Topics:

2,849 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...