Question about 2001 Chevrolet Tahoe

1 Answer

How do you get wires from under the hood to in the cab chevy s10

I just baught some extra lights and mounted them on my bumper now how do I get the wires into the cab? I cant find the hole

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

There should be ruber plugs under cab on both sides at back of cab.

Posted on Jan 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Detailed instructions on front bumper removal. NOTE: From all the videos, it appears the CAB is different than the sedan. An example is the grill does NOT come up with the hood.

Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

Oct 16, 2015 | 2003 Audi A4 Cabriolet

1 Answer

Is their a master fuse for the fuel pump and lights on a1991 Chevrolet s10 truck.if so what's the location

There are 2 fuse locations. Under hood and in cab, under dash on drivers side.

Nov 16, 2014 | Cars & Trucks

2 Answers

Front bumper

if can repair wires pig tails with sockets can be gotten from chevy to repair light. take jack and 2x4 jack up bumper if picks up truck before bends all the way use big hammer hit on 2x4 with pressure on bumper just be carefull on up swing bumpers are springy.

Aug 05, 2012 | 2002 Chevrolet Silverado 2500HD

2 Answers

Trying to locate the ignition module for chevy blazer s10 1994

Ignition module sits in the ignition distributor, remove distributor cap, there will be two elec. harness plugs, the one with two wire's is for the pick up coil, the other one is for the ignition module, just unscrew module out of distributor and install new one.

Sep 23, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

2001 s10 hood wont open with latch, tried bouncing hood while latch pulled but will not work. What now, read remove grill but looked at instructions, said open hood take out four screws under hood.

look at the cable sounds like when you pull the release lever the cable is sticking and not moving enought to pull the latch over usually you can reach up from under and give it an extra pull ,have someone else pull the lever in the truck while you look up under the bumper you should be able to see if the latch is moving

Apr 15, 2010 | 2001 Chevrolet S-10

1 Answer

How do I replace my starter?

Open hood.
Disconnect negative (-) batter cable
Locate the starter (under vehicle).
Remove electrical connections. (be sure to remember/take a picture/ make a drawing/ or mark which wires go to what posts)
Remove mounting bolts.
Remove starter, replace with new starter
Install mounting bolts
Install electrical connections

Jan 06, 2010 | 1990 Chevrolet S-10 Blazer

2 Answers

Where is timing wire bypass on a 94 chevy pick-up truck

Hello mjtee212.

The timing connector in previous years to yours was under the hood. But in 1994 it was moved inside the cab. You will be able to find it under the glove box next to the heater box. The wire is tan with a black stripe.

Thank you for using FixYa !


Dec 02, 2009 | 1994 Chevrolet C2500

1 Answer

2009 chevy expres trailer wiring harness

Ask dealer if it has a towing package on it. If it does, you usually just pop fuse in under hood for electric brakes, and harness to adapt into is usually near or at rear bumper. Even if it doesn't have brake wire, you should still be able to install adapter at rear,for lights etc. which is available from dealer or auto supply places, then you may have to run electric brakes separate.

Feb 21, 2009 | 2008 Chevrolet Express

Not finding what you are looking for?
2001 Chevrolet Tahoe Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides