Question about 2003 Mercedes-Benz C-Class

1 Answer

Front passenger door lock jumps up and down when locking car

This occurs when either using the ignition key on the automatic self locking that operates above 15kph

Posted by on

  • frommontreal Apr 22, 2009

    lock jumps up and down too!!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 241 Answers

You have a vacuum problem.
all your locking mechanisim works under vacuum lines, when you open one all open same if you close it all close.
try to unscrew lock tip a little bit like 1/4 of an inch and try it.
it locks also like the sensor is not detecting when it's lock or open.

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Unlock Child lock on nissan if the lock is on and dont open from outside


All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h).
? All doors unlock automatically when the ignition is placed in the OFF position.
The automatic unlock function can be deactivated or activated. To deactivate or activate the automatic door unlock system, perform the following procedure: 1. Close all doors.
2. Place the ignition switch in the ON position.
Within 20 seconds of performing Step 2, push and hold the power door lock switch to the position (UNLOCK) for more
than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each setting change.
When the automatic door unlock system is deactivated, the doors do not unlock when the ignition switch is placed in the OFF position. To unlock the door manually, use the inside lock knob or the power door lock switch (driver's or front passenger's side).
NOTE:
The automatic door unlock function can be changed using the Vehicle Settings in the vehicle information

Sep 30, 2016 | Nissan Pathfinder Cars & Trucks

1 Answer

Service immobilizer light is on an car wont start. It's a 2004 Pacifica


You are using an outdated browser. Please upgrade your browser to improve your experience.
Electrical • Vehicle Theft Security • Description Report a problem with this article

DESCRIPTION

VEHICLE THEFT SECURITY SYSTEM

The Vehicle Theft Security System (VTSS) is designed to protect against whole vehicle theft. The system monitors vehicle doors, and ignition action for unauthorized operation.
The alarm activates:
  • Sounding of the horn
  • Flashing of the headlamps/park/tail lamps
  • An engine kill feature (with SKIS)

SENTRY KEY IMMOBILIZER SYSTEM

The Sentry Key Immobilizer System (SKIS) is designed to provide passive protection against unauthorized vehicle use by disabling the engine, after two (2) seconds of running, whenever an invalid key is used to start the vehicle. The SKIS is active whenever the ignition is on and does not require any customer intervention. The primary components of the system are the Sentry Key Remote Entry Module (SKREEM), Sentry Key (ignition key with a transponder molded into the head), indicator light, Body Control Module (BCM), and the Next Generation Controller (NGC). The SKREEM is mounted on the ignition switch/lock cylinder assembly with the molded, integral antenna mounted around the ignition housing. The indicator light, is located instrument panel switch pod, just to the right of the instrument cluster.
Electrical • Vehicle Theft Security • Operation Report a problem with this article

OPERATION

VEHICLE THEFT SECURITY SYSTEM

Upon failure of proper SKREEM communication to the Next Generation Controller (NGC), the NGC will shut off fuel after two seconds of run time. The engine will not re-crank on the key cycle that the failure occurred, a full key down sequence must be performed for the engine to crank again. After six consecutive fuel shut-offs, the engine will no longer crank on subsequent key cycles. The failure must be corrected and a valid communication process between the SKREEM and the NGC must occur for the engine to crank and start again.
The electronics for the VTSS are part of the Body Control Module (BCM). The system is armed when the vehicle is locked using the:
  • Power door lock switches (with any door ajar)
  • Remote Keyless Entry transmitter.
  • Door Cylinder Lock Switches.
For vehicles equipped with SKIS, the doors do not have to be locked to enable the fuel shut off feature.
After the vehicle is locked and the last door is closed, the set LED indicator in the instrument panel switch pod will flash quickly for 16 seconds, indicating that arming is in progress. If no monitored systems are activated during this period, the system will arm and the LED will flash at a .5 Hertz (Hz) rate. If the liftgate is open, the LED will change its flash rate.
This indicates that the system is armed. If fault is detected on the driver key cylinder input, the indicator LED will remain solid during the arming process, although the system will still arm. If the indicator LED does not illuminate at all upon door closing it indicates that the system is not arming.
Passive disarming occurs upon normal vehicle entry by unlocking either door with the ignition key/remote transmitter. This disarming will also halt the alarm once it has been activated.
A tamper alert exists to notify the driver that the VTSS had been activated. This alert consists of 3 horn pulses when the vehicle is disarmed.
NOTE: The VTSS will not arm by pushing down the door lock mechanism. This will manually override the system.
For Door Cylinder Lock Switch service, (Refer to 8 - ELECTRICAL/POWER LOCKS/DOOR CYLINDER LOCK/UNLOCK SWITCH - REMOVAL).
If the VTSS is triggered, the horn will pulse, headlamps/marker lamps will flash, and the VTSS warning lamp will flash. If BCM determines the threat to be false and the VTSS is not triggered again, the system will shut down and rearm itself after three minutes. If a trigger is still active, the alarm will continue for an additional 15 minutes without the horn. The VTSS monitors the passenger compartment.
NOTE: System will not arm if passenger compartment is not secure.

ARMING THE VTSS - METHOD A

  1. With the key removed from the ignition lock and any door open (excluding liftgate), actuate one of the following:
  • Power door lock button to LOCK,
  • Key fob LOCK button
  • Driver door lock key cylinder to locked position.
  • Close all opened doors. Liftgate can remain open.
  • After the last door is closed, an arming time-out period of sixteen seconds will start, then the VTSS will become armed.

    ARMING THE VTSS - METHOD B

    Actuating the key fob transmitter LOCK button, key locking the front doors with the doors closed and the ignition locked will begin the arming time-out period. If method A, 16 second time-out sequence was in process when method B was actuated, the 16 second time-out will restart from the time of the second actuation.
    If the security lamp does not illuminate at all upon final door closure, it indicates that the system is not arming.
    The current VTSS status armed or disarmed shall be maintained in memory to prevent battery disconnects from disarming the system.

    TRIGGERING THE VTSS

    After the VTSS is armed, the following actions will trigger the alarm:
    • Opening any door (excluding liftgate).
    • Turning the ignition to the RUN position.
  • NOTE: When the VTSS is ARMED, the interior power door lock switch ?UNLOCK? will be disabled until the vehicle is disarmed.
    CAUTION: The VTSS indicator LED will trigger and engine will continue to run if the vehicle is equipped with SKIS and the proper key is used to start the vehicle. This condition will occur if the VTSS has been triggered. If valid key is used, VTSS will disarm.

    CENTRAL LOCKING/UNLOCKING

    This vehicle theft security system feature allows you lock all the doors with the key by using the drivers door lock cylinder.
    All vehicle doors and liftgate are locked with the first turn of the key to the LOCK position from the drivers door. A double activation feature of central unlocking requires you to turn the key in the door lock cylinder to the unlock position two times within two seconds to UNLOCK all vehicle doors at once.
    The first turn of the key in the door lock cylinder will disarm the system (the driver door cylinder lock switch connected to the back of the driver door lock cylinder) and unlock your drivers door. The second actuation within two seconds will then unlock all doors and the liftgate.

    SENTRY KEY IMMOBILIZER SYSTEM

    The SKIS includes keys from the factory which are pre-programmed. Each SKIM will recognize a maximum of eight Sentry Keys. If the customer would like to own additional keys other than those provided with the vehicle, they can be purchased from any authorized dealer. These keys must be programmed to the SKREEM on the vehicle in order for the system to recognize them as valid keys. This can be done by the dealer with a DRB III® scan tool or by a customer if this feature is available in their market and they have two (2) valid keys already available to them. The SKIS performs a self-test each time the ignition switch is turned to the ON position and will store Diagnostic Trouble Codes (DTC's) if a system malfunction is detected. The SKIS can be diagnosed and any stored DTC's can be retrieved using a DRB III® scan tool as described in the appropriate Body Diagnostic Procedures manual.
    With the light being on there is a code stored in the computer that controls anti-theft , Your best bet would be to take your vehicle to the dealer !




    Aug 20, 2016 | Cars & Trucks

    1 Answer

    Doors will not open with the key that I have for the ignition. Any ideas?


    Auto Repair : Power Door Lock Troubleshooting

    sofia2013.com/auto-repair-power-door-lock-troubleshooting/
    Jul 29, 2014 - can't use the key i have to go through the passenger door and unlock it ... when I get out of my 2003 Honda Accord, and leave the keys in the ignition, ... Any ideas why all the doors wont lock even pushing the lock button in the

    Remote won't unlock passenger or rear doors - TDIClub Forums

    https://forums.tdiclub.com/showthread.php?t=355194
    Jun 4, 2014 - Will unlock the drivers side door and rear hatch (wagon). ... Any ideas, ... I have the VCDS and tried to program the remote with no success. ... precisely, but it was something like put the key in ignition, turn to acc, then push the unlock button. .... fiddling around with passenger door did not produce any result.

    Door locked with key in ignition - TDIClub Forums

    https://forums.tdiclub.com/showthread.php?t=125387
    Dec 17, 2005 - Anybody have any ideas on this? I know there should ... The door willlock with the key in the ignition and the car running. It does automatically ...

    Ignition key won't open door - 8th Generation Honda Civic Forum

    www.8thcivic.com > ... > Mechanical Problems & Technical Chat

    Dec 20, 2015 | Cars & Trucks

    1 Answer

    Opening the drivers door doesnt automatically open the passangers door


    Some vehicle locking systems allow a single button press to unlock the driver's side door and require a second button press to unlock the passenger side door. Likewise, use of the key to unlock the driver's side door does not automatically unlock the passenger side.

    Mar 25, 2014 | Dodge Stratus Cars & Trucks

    1 Answer

    The doors lock automatically on my daughter's '99 Cougar. This has happened to me when I left the keys in the ignition and closed the driver's door. After AAA came and unlocked the doors, I removed the...


    shorted wiring in doors or shorted door lock actuator in door. A grounding of a wire makes them lock normally. SO, any bare wire touching metal will ground it and lock the doors.

    Principles of Operations
    The Door Switch Lock Function When a door lock switch is moved into the lock position or a door lock cylinder is rotated to the lock position, the door lock switch grounds the lock circuit input to the central security module (CSM). The CSM then provides 12 volts to one side of the door lock actuators contained in the door latch unit and simultaneously grounds the other side of the door lock actuators. This completes the door lock actuator circuit, causing the door lock actuators to rotate a cam assembly, which then locks the doors. The 12 volts that the CSM provides to the door lock actuators are provided to both door lock actuators from a single pin on the CSM electrical connector.
    The Door Switch Unlock Function When a door lock switch is moved into the unlock position, the door lock switch grounds the unlock circuit input to the CSM. The CSM then provides 12 volts to the opposite side (relative to locking the door) of the door lock actuator(s) contained in the door latch unit and simultaneously grounds the other side of the door lock actuator(s). This completes the door lock actuator circuit, causing the door lock actuator(s) to rotate a cam assembly in the opposite direction, which the unlocks the door(s). The 12 volts which the CSM provides to the door lock actuator(s) are provided to each door lock actuator from the individual pins on the CSM electrical connector.
    --------------------------------------------------------
    CSM Self-Test The CSM has a self-test which can be entered into by using a diagnostic tool. This self-test will monitor the following CSM door lock inputs:
    • Unlock switch (DTC B1311)
    • Lock switch (DTC B1300)
    • Exterior lock switch (DTC B1309)
    • Exterior unlock switch (DTC B1341)
    Before running the self-test, the following conditions must be met:
    • The ignition switch must be in position II
    • The driver and passenger doors must be unlocked
    • The driver and passenger doors must be opened
    • The hood and liftgate must be closed
    • The set/reset switch, and liftgate release switch are not actuated
    It is important to note that all of the diagnostic trouble codes (DTCs), with the exception of B1551 and B1553 can be retrieved with the self-test. DTCs B1551, and B1553 are continuous and will only be retrieved if the liftgate release is operated prior to retrieving the continuous DTCs.
    Inspection and Verification
    1. NOTE: Make sure that the battery is fully charged before starting electrical diagnosis.
      NOTE: Prior to carrying out the CSM Self-Test, make sure that both the driver and passenger doors are open.
      Verify the customer concern.
    1. Visually inspect for obvious signs of mechanical and electrical damage.


    Visual Inspection Chart Mechanical Electrical
    • Binding latch mechanisms
    • Binding linkage
    • Misaligned door
    • Central junction box (CJB) fuse(s)
    • Wiring harness
    • Electrical connector(s)
    • Door lock switch(es)
    • Door lock actuator(s)


    Module Controlled Functions
    The central security module (CSM) covers the following functions:
    • Central door locking
    • Double door locking
    • Anti - theft alarm incorporating
      • forced entry
      • radio theft
    • Radio frequency remote control of
      • central door locking
      • panic alarm
      • driver door unlock
      • liftgate unlock
    For additional information, refer to Section 419-01A Anti - Theft - Active, Section 501-14A Handles, Locks, Latches and Mechanisms, and Section 501-14B Keyless Entry/Computer Operated Locks.

    The CSM is in the passenger side kick panel I think.

    Good luck

    Jan 25, 2011 | 1999 Mercury Cougar

    1 Answer

    Automatic passenger door lock


    You should replace power door lock at front passenger side, you can use any 'universal' power door lock. its an unit with a small motor inside that have a mechanism to up and down according electricity from the actuator (master door lock at driver side)
    Hope this help :-)

    Sep 13, 2009 | 2005 Toyota Corolla

    1 Answer

    Door Lock Malfunctioning


    power door lock solenoid may need replacement

    Jul 04, 2009 | 2007 Mercedes-Benz C230 Sedan

    1 Answer

    Central locking wont stay open


    Here's what I suspect is happening. The door locks will lock and unlock normally when the key is OUT of the ignition. If the key is IN the ignition, the doors cannot be locked (manually, key fob, or otherwise, if the system is operating as designed - prevents the doors being locked when the key is in the ignition). I've seen this problem before, but on a Santa Fe, not an Accent. The ground signal of the right hand front passenger door was lost, and the doors automatically locked. Perhaps something similar is happening in the circuit between the ETACS module and the right front passenger door lock/unlock actuator. Could be anywhere in the circuit.



    d05b136.gif
    ab4c712.gif These wiring diagrams may be helpful. The relays expecially may help solve this issue. As you can see, these relays are also controled by the ETACS module (Remote Keyless Entry).

    67dc553.gif

    Mar 31, 2009 | 2003 Hyundai Accent

    Not finding what you are looking for?
    2003 Mercedes-Benz C-Class Logo

    246 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercedes-Benz Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Michael Contreras
    Michael Contreras

    Level 2 Expert

    164 Answers

    Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...