Question about 2000 Hyundai Sonata

2 Answers

Hyundai Sonata 2000 model 4 cylinder. while driving the stopped and wont start. changed timing belt, balancer, tensioner and timing sensor, coils, fuel pump, plus another sensor that fits near the coils. the starts but only for a few seconds, shakes alot and the engine dies out. Please help....

Posted by on

  • Anonymous Jan 11, 2009

    need diafragm the timing belt

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi there. I can solve this dangerous problem you are having. You would loose acceleration at lights and intersections, the engine will shake and revs can go crazy. The issue is the MAF (mass air flow) sensor. It was recalled in 2001 as a safety problem as people died driving this model of sonata. If you connect your comp up to a diagnostic machine you will find its the MAF the problem is a problem that is hard to ctah on a diagnostic machine though as it comes and goes. You will need to replace the MAF ASAP as you can die from this fault and hyundai will not care due to the age of this car.

Posted on Apr 13, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

Hi!
You have done a general service. Make sure fuel pump's output pressure is about 35-40 psi and there is not water in fuel tank.
If no result check all cable connections to be clean and well fitted (better unplug inspect and replug them).

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE SERPENTINE BELT LOCATED ON A 2003 HYUNDAI SONATA


Vehicles Covered: Hyundai Sonata 2002-2004 (2.4L & 2.7L Engines)

In 2003, Hyundai produced two types of Sonata:
Available engines:
4 Cylinders 2.4L VIN "S", MFI DOHC - see Figures 1 and 3.
6 Cylinders 2.7L VIN "H", MFI DOHC - see Figures 2 and 3.

To differentiate between these types of 2003 Hyundai Sonatas, the VIN 8th digit (Engine Type) will either be "S" or "H" as in the table above.

To locate the Engine drive belt, jack up the vehicle & place it onto jack stands, then slide under the car (toss a cardboard mat down first), then, once under the car, remove the (plastic) engine splash shield. Once removed, the drive & accessory belts are easily observed.

12_27_2011_5_25_29_am.jpg

Fig. 1 Accessory Drive Belt Routing 2.4L (4 cyl) Engine - Hyundai Sonata
The "COMPRESSOR" refers to the A/C compressor, and "GENERATOR" refers to the Alternator.


12_27_2011_5_27_01_am.jpg

Fig. 2 Accessory Drive Belt Routing 2.7L (6 cyl) Engine - Hyundai Sonata
The Belt Routing on the Left is "With A/C", on the Right is "without A/C"

Inspection - Drivebelt and Accessory Belts

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. Worn or damaged drive belts should be replaced.

Drivebelt Removal & Installation - 2003 Sonata (2.4L and 2.7L engines)

Raise and support the vehicle.
Remove the engine splash shield.
Rotate the drive belt tensioner clockwise to release the drive belt tension.
Remove the drive belt from the alternator.
Slowly release the drive belt tensioner.
Remove the drive belt from the accessory drive pulleys.

To install:

Install the drive belt to the accessory drive pulley.
Rotate the drive belt tensioner clockwise.
Install the drive belt to the alternator.
Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
Slowly release the drive belt tensioner
Install the engine splash shield.
Lower the vehicle.

Here's the best illustration I can find of the Hyundai 2.4L and 2.7L engines - the drivebelt seems to be located on the passenger side of both of these transversely mounted engines.

12_27_2011_6_03_16_am.gif

Fig. 3 Hyundai 2.4L and 2.7L engines - Underhood sensor locations 2002-2004 only

Glossary of Acronyms
---------------------------------
A/C - Air Conditioning
DOHC - Dual Overhead Cam
MFI - Multi-port Fuel Injection

Dec 25, 2011 | Hyundai Motor 2003 Sonata

2 Answers

Timing belt replacement interval


My rule of thumb for Timing belts:
replace at 60,000 miles, and every 40,000 miles thereafter. Having said that, I often let
cars go until the timing belt starts showing signs of wear (usually every 50K - 75K miles)

But www.autozone.com (register free at www.autozone.com) is recommending for your
car driving in "severe driving conditions" (aka normal stop-start driving) that your 2000 Sonata
have:
60,000 miles - replace
90,000 miles - inspect for wear
120,000 miles - replace
150,000 miles - inspect for wear

The 155 page owners manual (I found one at the link below - you may prefer to try Hyundai)
makes no mention of the timing belt at all.

http://www.scribd.com/doc/29113477/2000-Hyundai-Sonata-Owners-Manual

Jan 02, 2011 | 2000 Hyundai Sonata

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

1 Answer

How do i change the water pump on 2004 sonata 4 cylinder?


Hyundai Car 1999-05 - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
c84998b.jpg

Fig. Water pump assembly-1.8L and 2.0L engines

9eb0fb7.jpg

Fig. Exploded view of the water pump assembly and related components-2.0L engines


Hope this help; TY for using Fixya (remember comment and rated this).

Mar 31, 2010 | Hyundai Motor 2004 Sonata

2 Answers

2003 Hyundai Sonata vvvibbbrraattteess!!!!


There are Two Balance Shafts on the 2.4. Did your mechanic also change the balance shaft belt when he changed the timing belt? If he didn't, you'll want to do that. Since you mentioned the old belt was missing teeth, those loose teeth flying around could have damaged the crank position sensor and sensor blade (tone wheel). Also, the front balance shaft (on the side of the engine nearest the radiator), has THREE different positions when the timing mark is lined up - here's the glitch - ONLY ONE of them is the correct one - this is probably where your vibration is.

Oct 10, 2009 | Hyundai Motor 2003 Sonata

1 Answer

2002 Hyundai Sonata have a timing belt or chain


timing belt and yes the belt and tensioner needs changed every 60k and if its a 4cyl. the balance belt also needs replaced

Aug 18, 2009 | Hyundai Motor 2004 Sonata

1 Answer

I have a hyundai sonata 2000 it is 2.0 16valve wont start


Firstly, what's a TDC sensor?.. the crank position sensor? If so, on the four (4) cylinder, it's located behind the timing belt cover at the crankshaft.. if it's the 2.5 V6, it's located behind the LH exhaust manifold on the engine block.

Jul 28, 2009 | 2000 Hyundai Sonata

1 Answer

2000 sonata crank sensor


change the coil pack.

Jun 09, 2009 | 2000 Hyundai Sonata

1 Answer

Hondai sonota


Which engine? 4 cylinder (2.4 lit) or V6 (2.7 lit)? Two different procedures as well as different belts. The 4 cylinder also has a balance belt. See next image:
42e8a57.jpg
Here's the 2.7 V6 belt:

44efb27.jpg
The replacement procedure is nearly the same at the start (removing, accy drive belts, pullys, support engine & remove front engine mount, remove T.B covers, disconnect Cam Position Sensor & Crank Position Sensor connectors, etc.). When you get to this point on the V6, you also have to remove the front engine mounting bracket from the front of the engine (4 14mm bolts, also a 12mm bolt which bolts the dipstick tube to the side of it) Put crank shaft at TDC (top dead center w/ALL timing marks aligned) remove hydraulic tensioner (2 12 mm bolts), then remove the belt. You'll need to recompress the hydraulic (auto) tensioner in a vise and insert a retaining pin through the pin-holes at the top (through the tensioner piston) to keep it compressed when you reinstall it. Otherwise, you won't be able to install it. Assembly is reverse order of dissassembly. Inspect your pullys while you're in there (check for pully bearing noise, leaking grease, smooth rotation, also the water pump pully, etc.) Replace components as needed. Careful not to damage Crankshaft Position Sensor wire harness.

The 4 Cylinder is quite different. You not only change the timing belt, but also the countershaft (balance) belt, which is behind the crank position sensor blade. IMPORTANT: ALL TIMING MARKS ALIGNED BEFORE REMOVING ANYTHING) There are two (2) counter-shafts (balance shafts). one driven by the timing belt, the other by the crankshaft sprocket behind the timing belt sprocket at the front of the crankshaft.
70f048d.jpg1999205.jpg366ecea.jpg b8013a3.jpg

Jun 02, 2009 | 2001 Hyundai Sonata

1 Answer

Car misses and cuts out!!!


Ron

It sounds like you have done everything Unfortunately it is hard to diagnose because al of the above is what I would have done

I have a 2000 Hyundai Elantra and had a similar problem and I took the car to Cotterman transmission
(because it would hardly go engine rattled and lurched and stalled) they put an electronic diagnostic and said I had a mis fire on cylinder 2 and 4

I bought the best spark plug wire and boot kit and 4 plugs and replaced and it runs like a top!

It almost sounds like you have bad gas I would remove the air cleaner and spray starting fluid
into the carb while car is running ad see f it smooths out this will tell you if it is gas



Best of luck

Jan 06, 2009 | 2000 Hyundai Sonata

Not finding what you are looking for?
2000 Hyundai Sonata Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...