Question about Toyota Camry

1 Answer

Loud noise when I put the car in gear. Will not ingauge into gear

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

With what you said and nothing else to go on id say you have a brokev cv joint there is 1 on each side

Posted on Jan 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Manual Transmission loud metal noise 5th gear doesn't work


check the drain plug magnet for metal bits . If any the box has to come out 4.th gear is straight shaft connection and 5 gear connects from the cluster shaft up to the out put shaft . On either side is a rear main bearing and from your description if that bearing is failed then the 4th gear syncro will not align properly and the gear for 5th will be out of alignment so the syncro to work will not work

Mar 15, 2014 | 1993 Ford Escort 4 Door

1 Answer

When I put my 98 Maxima in gear, it starts making a very loud noise under teh car. It will go into gear and move, but the noise will only stop if I put it in park or neutral.


If noise comes from transmission in D range -no drive.Then i thing of AT internal problem. If in D during driving then you have to check drivetrain,like axles or bearings. or AT.

Dec 10, 2013 | 1996 Nissan Maxima

1 Answer

95 Buick lesabre making loud grinding noise when starting. Once started runs and drives fine no noises


Yes, you are probably right about the spacer or shim. A salvage yard should have lots of them for little or nothing. When you remove the starter for the spacer, check the drive gear end of the starter for severe wear. If it is chewed off very bad, have a new drive gear put on, or replace the starter.

Nov 05, 2012 | Buick LeSabre Cars & Trucks

1 Answer

1995 GMC SONOMA makes a loud sqeaking noise when i take off in the first to third gear, after third gear it stops, but when i get to a stop sighn it starts all back over, loud noise.


This type of noise is likely to be a universal joint that is worn out in the drive line. have a shop put it on a lift and inspect the joints.

Jun 06, 2012 | 1995 GMC Sonoma

1 Answer

TAPPING NOISE, NOW IT WON'T GO INTO GEAR WITHOUT LOUD GRINDING NOISE AND ACTS LIKE TRANSMISSION WON'T ENGAGE TO DRIVE


If it is an automatic transmission, first check the fluid level. If it is low, fill it up and try it again. If the level is fine, then there is a bigger issue and you should seek a professional's help.

Jun 18, 2017 | 1996 Buick Century

1 Answer

When driving my 2000 Olds Bravada, it has a loud roar noise that sounds like when a semi truck is taking off before the gears are shifted. Transmission shifts easily into gears, just this loud roar noise...


If there's a loud roaring noise all the time, then your muffler probably has a hole in it, time to get a new full or partial exhaust pipe.

If the noise goes when it changes gear, then you've probably got a gear box or thrust bearing problem.

Apr 22, 2011 | 2000 Oldsmobile Bravada

1 Answer

When i put the car in drive it make a loud noise and it


the orbital gears in the trans are bad basically you need a transmission

Mar 03, 2010 | 1997 Acura CL

4 Answers

1996 Audi A4 Quattro has a noisy rear differential


It's the wheel bearing. Guaranteed. Just replaced mine. Go to Audiworld tech articles for step by step instructions on how to test the wheel bearings. They must have been put in wrong last time or they just went out again.

Oct 13, 2008 | 1996 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...