Question about 1997 Ford Econoline

1 Answer

Flasher lights and turn signals are not working-fuse?

I think I've blown a fuse but don't know which is the fuse which needs replaced.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

Pull one at a time & replace as you find bad ones

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New flasher relay good fuse no four way flasher no turn signals


you need to check the bulbs holders and wiring even a blown bulb will not blow the fuse and an damaged wire or bulb holder will as it will make earth and live go together. there are also fuses for left side and right side turning lights cannot remember rating think they are 10amp.

Mar 19, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My turn signals don't work and I've checked the bulbs, fuses & flasher.


About all that is left on the list is the turn signal switch.
Do you have power in and out of the switch ?

Feb 04, 2013 | 1995 Buick Skylark

3 Answers

1994 Chevy C1500 truck. No rear brake lights


Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Oct 29, 2012 | 1994 Chevrolet C1500

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

Turn signal dosent work


you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace

Mar 15, 2011 | 1997 Dodge Ram 1500 Club Cab

3 Answers

Turn signals dont blink.


You need to replace the turn signal flasher, it's a cylinder shape and may be silver or gold in color. When it goes bad, the turn signals stop flashing. Good luck and keep me posted.

Feb 16, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

No turn signals or hazards


there could be two things wrong here.
1 the flasher unit is defective and needs replacment i think that indicator and hazzard are on the same flasher unit.
2 a fuse has blown and needs repacement or it has a bad conneciton
both should be in the fuse compartment.

Nov 13, 2009 | 2004 Chevrolet Silverado

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

1 Answer

Diagram


ok, the dash does not show the blinker is on, did you check the front and back to see if any of the turn signals were on, but not blinking? Also the side marker lights should light up if the turn signals aren't working, do they? Let me know. Next check the fuse box, it's on the driver side, under the dashboard. The fuses will be labeled, check the fuse for the turn signals.
Check to see if it"s blown. If it is, or you aren't sure, replace it with one of the same amperage (the # of amps is on the fuse). The fuses can just be pulled out to check them. If you still don't have working blinkers, go back to the fuse block under the dash. There are 2 round canister shaped units plugged into the fuse block. One of them is the turn signal flasher. They are about the diameter of a quarter, and a bit over an inch thick. If your emergency flashers are working, unplug one of the flashers. If they don't work after unplugging one, then you just unplugged the emergency flasher, so the other one is the turn signal flasher. Replace with a new one, identical to the old one. Let me know when you have followed all these instructions and what happens. countrycurt0

Aug 11, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Ford Econoline Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...