Question about 2004 Cadillac Escalade

1 Answer

Liftgate will not unlock when i use power lock or the remote keyless entry transmitter. I checked the fuse LOCKS (rear doors and liftgate power lock relay feed) it is fine. The rear doors do unlock using both options. What do i do? Help.

Posted by on

  • 3 more comments 
  • jjarmend Mar 16, 2009

    all the other doors open except the liftgate on the 2005 tahoe.

  • Anonymous Mar 24, 2014

    Liftgate on my Cadillac SRX won't unlock with the door or key remote.

  • Anonymous Mar 24, 2014

    actuator doesn't unlock

  • Anonymous Mar 29, 2014

    alert comes on every time i start the motor. how can i fix it? thanks!

  • Anonymous Mar 29, 2014

    alert comes on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

If it was mine I would take the rear inside door panel off and see if there is any rust or bind in the power door lock motor itself and also make sure that no one has broken a key off or stuck anything in the lock cause I had an expedition with this same problem and it was a broken key in the lock

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you reset the alarm system on a 98 olds silhouette after it triggers without the remote entry


Theft Deterrent Arm/Disarm Modes
Important: Although mode 2 provides increased security, the content theft deterrent system disarms only by pressing unlock on the keyless entry transmitter. This can pose a problem if the keyless entry transmitter is damaged, lost, or inoperative for any reason while you attempt to disarm the content theft deterrent system.
Mode 1: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter. The system does not arm when you lock the doors with a power door lock switch.

Mode 2: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the doors with the keyless entry transmitter. The system does not disarm when you unlock the doors with the key.

Mode 3: The system arms when you lock the doors using a power door lock switch or the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter.
Changing the Feature Customization Modes
  1. Turn off the IP dimmer switch.
  2. Turn the ignition switch to the LOCK position.
  3. Remove the BCM PRGRM fuse.
  4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
  5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.
  6. The BCM flashes the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode 4 repeats the sequence starting with mode 1.
  7. Complete the following steps in order to change the theft deterrent arm/disarm mode:
6.1.
Insert the key in the left front, right front, or liftgate door lock cylinder.


6.2.
Rotate the key from the center to the unlock position.


6.3.
Press the horn button on the remote keyless entry transmitter.


6.4.
Count the number of chimes that you hear. The number of chimes tells you which mode you have set.


6.5.
Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates the mode that you want.


6.6.
Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:

  1. Turn the ignition switch to the LOCK position.
  2. Reinstall the BCM PRGRM fuse.
If you are unable to change locking modes Theft Deterrent System Feature Customization Inoperative

Aug 25, 2015 | Cars & Trucks

1 Answer

Envoy hatch lock


There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Apr 14, 2014 | GMC Envoy XL Cars & Trucks

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

1 Answer

I just bought an equinox 2005 LS and I dont know how to lock the rear door.


To unlock the liftgate, press the unlock button on the Remote Keyless Entry (RKE) transmitter twice or use the power door lock switch.
To lock the liftgate, press the lock button on the RKE transmitter or use the power door lock switch. The liftgate does not have a key lock cylinder.
To open the liftgate, pull up on the handle located in the center of the liftgate.
When closing the liftgate, use the molded handles to pull the liftgate down. Push the liftgate closed until it latches.

Jul 08, 2011 | 2005 Chevrolet Equinox

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

1 Answer

Key Pad Entry does not work


does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
  • Keyless entry keypad
  • Keyless entry remote transmitter
  • Central junction box (CJB) Fuse F222 (20A)
  • Circuitry
  • Generic electronic module (GEM)
------------------------------------------------------------------------
  • No communication with generic electronic module (GEM)
  • Generic electronic module.
  • Circuitry.
  • REFER to Section 419-10 .
------------------------------------------------------------------------------------

Mar 08, 2009 | 2003 Ford Taurus

Not finding what you are looking for?
2004 Cadillac Escalade Logo

511 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...