Question about 2006 Dodge Ram 3500 Truck

3 Answers

Changing front turn signal 2006 dodge truck

Do I need to completely remove the whole light housing to change the turn signal.

Posted by on

  • Anonymous Mar 26, 2014

    install clear lens housing

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Yes you do. You have to take the whole assembly off the truck to fix the problem. I tried wesbingham3's way and it was a dead-end. I then had to call a Dodge dealer and they told me that you had to take the whole assembly off the truck which turns out easier than it seems. All you have to do is remove the two bolts that are by the radiator and pull the assembly straight off the truck. It helps when pulling it off if you already have the headlight out of the assembly (which can be removed from atop of the assembly). Once you get the assembly off the truck then all you have to do is change the bulb and replace the assembly. Once I figured it out it only took me 5 minutes.

Posted on Jan 28, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You also need to remove the bolt that is just behind the plug in the wheel well. After that, the assembly should just lift off.

Posted on Mar 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

No. You can reach in from the bottom of the truck and give the light about 1/4 of a twist and it will come out of the housing. Then you can disconnect it from the wire harness where you can see it.
Good luck.

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the turn signal bulb on my 1993 dodge dynasty


Front or rear? If its the rear light, you should check inside your trunk. Move any liner that may be over the light housings, and look for fasteners, usually plastic wing nut types, that you can remove and lift out the whole tail light assembly. Once out, you can change the individual bulbs.

If it's the front turn signal, I think that's part of the headlight assembly, and you may have to remove the whole assembly to get at the bulbs. Look for screws in the top cross member, and in the panel next to the radiator to remove the assembly.

Jan 16, 2016 | 1993 Dodge Dynasty

1 Answer

Change a turn signal bulb on a 2006 dodge grand caravan


The rear remove two push in pins remove tail light housing replace bulb. Front remove screws holding head light housing replace bulb

Feb 28, 2015 | 2006 Dodge Grand Caravan

1 Answer

Pop off front lens jeep 2009 patriot


You guys are all very close but check this, on the Patriot you can't take the lens or housing out from the front. It has to be removed from the back. And in saying that, you don't have to remove the housing at all. The steps are as follows, #1) Remove the inner fender well cover. It's the black plastic covering that hides all the wiring and the engine compartment. There are 7 push screw retainers to remove and 3 philips screws. #2) Once the cover is removed, all you need do is reach your hand in behind the turn signal and twist the bulb and it's socket to the left to remove from the housing. #3) Now that you have the light and socket out, you are just left with pulling out the red clip on the socket and pinching the black tab while you pull out the bulb. It's just that simple. Now if your housing is cracked or blemished and you have to completely remove it, then you will need to remove 3 torx bit screws that attach it to the front fender. They go in from the back of the housing. And yes, they are T20's. I don't necessarily call this dismantling the whole front end. But it's not a 5 mins job either.

Jun 28, 2013 | 2009 Jeep Patriot

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

Left turn signal flashes faster than the right turn signal. how do i remove the bulb?


It depends on if its the front or the rear bulb. In the front the screws are mostly on the out side of the car. The baco screwa ar in side the trunk inside of the truck liner. You have to remove the hole light fixture from the car and then turn the bulb holder out to change the bulb

Dec 13, 2009 | 2006 Dodge Grand Caravan

3 Answers

I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


hi Paul

Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

Good luck.

Dec 02, 2009 | 2006 Cadillac SRX

1 Answer

How do you change the turning signal on ford contour sport?


This is for the 95-97 Contour. 98+ are different, because the light housing changed completely.
1. Open the hood.
2. In each front corner of the hood, there is a torx bolt, head about the size of a nickel. Removing this one bolt allows you to remove the corner marker/turn signal housing.
3. Once the housing is free, you have access to the back of the bulb holder. If I recall correctly, it's a half-twist to remove, but I'm not sure. Could just be barbed clips, or something. Anyway, from here should be no problem to figure out how to remove and replace the bulb.
4. Replace corner marker/turn signal housing, and re-install torx bolt. That's it!

Oct 11, 2009 | 1997 Ford Contour

2 Answers

Rear turn signal bulb


Open the trunk, behind the light you will see a plastic wing nut, remove it.
Then pull the carpeted trunk liner away and you will find 2 more plastic wing nuts. remove both of them and the wireing harness. the lamp will now com off the back of the car. twist the bulb base out and replace with new bulb.

You can go to www.chargerforumz.com with any other charger questions. use me Sandman2053 as a refrence. its FREE to sign up

Feb 03, 2009 | 2006 Dodge Charger

1 Answer

Changing Front Signal Lights


open the hood and there is one bolt on top/ It pops out be firm/ Please rate my response thank you very much

Feb 02, 2009 | 2006 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...