Question about 2005 Ford Explorer Sport Trac

Open Question

How to clear a p1000 code from 2005 explorer

How to carryout obd readiness test

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chrischronic
  • 235 Answers

SOURCE: 1997 FORD CODE P1000

a p1000 code means that the system has not run all checks since last memory erase. in other words after a code erase this code is set until the car has been driven for 2 drive cycles which is 20 to 25 miles then 20 to 25 miles again.

Posted on Apr 21, 2009

Ad
  • 14036 Answers

SOURCE: 2005 ford focus engine dies with obd ii codes 1233

CODE PO1233 - FUEL SYSTEM DISABLE OR OFF LINE.POSSIBLE CAUSE. INERTIA FUEL SHUTOFF IFS SWITCH NEEDS TO BE RESET.FPDM GROUND CIRCUIT IS OPEN OR SHORTED. CODE PO1235 FUEL PUMP CONTROL OUT OF RANGE. POSSIBLE CAUSE FP CIRCUIT IS OPEN OR SHORTED. FPDM IS DAMAGE. PCM HAS FAILED.

Posted on Sep 26, 2009

  • 836 Answers

SOURCE: how to clear a P1000 code from 2005 focus?

You need a either a code read or scanner.

Posted on Jan 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do codes P0411, P1000


P1000 code means the codes were cleared or the battery was disconnected
Powertrain Control Module (PCM) Reset Description All OBDII scan tools support the powertrain control module (PCM) reset.
The PCM Reset allows the scan tool to command the PCM to clear all emission-related diagnostic information. When resetting the PCM, a DTC P1000 will be stored in the PCM until all the OBD II system monitors or components have been tested to satisfy a drive cycle, without any other faults occurring. For more information about a drive cycle, refer to Drive Cycles .
The following events occur when a PCM reset is performed:
  • Clears the number of Diagnostic Trouble Codes (DTCs).
  • Clears the DTCs.
  • Clears the freeze frame data.
  • Clears diagnostic monitoring test results.
  • Resets status of the OBD II system monitors.
  • Sets DTC P1000.

P0411 Secondary Air Injection System Incorrect Flow Detected

neither of these could cause a no start or no crank problem . Is the battery good an do you have good connections on the battery ? Do the headlamps show bright when on ?

Oct 14, 2015 | 1997 Lincoln Continental

1 Answer

My ford escape 2008 model could not start after driving it last night. after diagnosis this is the code is showing me. P1000 18, 2, 10, 0 please refer to relevant technical manual. please what cani do


Code p1000 means on board diagnostic readiness test not complete (fail) Check battery connection, check connection of pcm (computer),
Another possibility is an OBD monitor concern occurred before complete of an OBD drive cycle
Looked up in OBD database for Ford vehicles

Sep 19, 2015 | Ford Cars & Trucks

1 Answer

What are the error codes p1000 and p1116


P1000-OBD System Readiness Test Not Complete

P1116-Engine Coolant Temperature Sensor Out
of Self Test Range

Mar 05, 2011 | 1998 Ford Explorer

1 Answer

Wats the code p1000 on my 2002 jaguar x type


P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.

Feb 18, 2011 | 1999 Jaguar XK8

2 Answers

P1000 code appeared. just replaced alt. recharged batt. wont start.


The definition for P1000 code is as follows:
OBD II Monitor Testing not complete
You may be experiencing ECM computer problems. Have it diagnosed by a certified ASE professional.

Feb 06, 2011 | 1998 Jaguar XK8

1 Answer

My scan tool says p1000 when i look up the codes on my f150 just woundering what p1000 is


Hello, my name is Ben. Here is the short answer: P1000 OBD-II Monitor Testing Incomplete
P1000 will be set anytime there is any interruption of power to the PCM. This action could be but is not limited to, changing the battery, clearing history codes, or reprogramming the PCM. If there are no other codes stored the P1000 will clear itself after several "driving cycles". I hope this helps you, Ben.

Jun 24, 2010 | 2002 Ford F150 Regular Cab

1 Answer

I cleared the three DTC codes previous asked, which were P0088, P0087,nad P2291, re-started the engine and getting a DTC Code P1000 can you tell me what this code is. The three previous codes started when...


P1000- on-board dianostic systems readiness test not complete, 1. obd monitors and drive cycle incomplete 2.keep alive memory(KAM) cleared, wat to do and try. remove power take off fuse(PTO) then cleared the code,disconnect pcm connector and visually check for corrosion

Jun 21, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

I have 2ooo chevy malibu and thos codes B 1000 U 1016


both codes mean the same thing. "obd readiness test not completed". p1000 should clear itself, any time battery is disconnected it will set this code. after you drive and it goes through its drive cycles, it should clear if all is ok. good-luck!!

Jan 23, 2010 | 2000 Chevrolet Malibu

3 Answers

What dose the code p1000 mean and p1645


P1645 EVAP Solenoid Output Circuit
P1000 Scan not complete. meaning it didnt finish scanning

Sep 14, 2009 | 2002 Jaguar X-Type

2 Answers

Fault code P1000 [18,2,10,0],Ford Fiesta 2005


P1000 means that you or someone has disconnected the battery,and the car has not been driven far / long enough for the computer to relearn its stratagies.
Engine light could be the fault of the speed sensor, or wiring to the sensor.

Jul 13, 2009 | 2007 Ford F

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...