Question about Cars & Trucks

1 Answer

2007 ford 5.7 crankshaft sensor... Is there a way to bypass the sendor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,366 Answers

Bypass it? Not if you want the engine to run. The engine computer requires a signal from the CPS to determine spark timing. So no signal, no spark.

Posted on Nov 09, 2012


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 2030 Answers

SOURCE: Crankshaft posistion sensor or ignition control module?

1) do you have a Check Engine Light On while running? If so find out what the code is
2) these engines are known for their CPS going can be tested on the car with a volt meter and turning the engine, but it isnt easy....I would have to err in the direction of changing the Crank Position Sensor.

Posted on Feb 02, 2010

  • 2620 Answers

SOURCE: 02 ford taurus crankshaft position sensor location

Its located in the front of the engine mounted to the timing cover near the crankshaft pulley.

Posted on Oct 29, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i bypass a sensor of an opel corsa utility 1.4 2006 model?

If you bent the crankshaft and are talking about the crankshaft sensor can't bypass it the car will not run without it

Jun 03, 2016 | 2006 Opel Corsa 1.4

2 Answers

Why it wont start

Run basic diagnostics. Spark? Correct fuel pressure? Compression?

Oct 07, 2015 | 2007 Ford Edge

1 Answer

Surging problem 2007 ford taurus 3.0

Tests/Procedures: 1. Unplug the mass air flow sensor and see if the concern is gone or improved. If so, suspect mass air flow sensor or circuit problem.

2. Unplug the alternator and see if concern is gone, if so, suspect the alternator or its circuits.

3. Unplug the camshaft position sensor and see if concern is gone, if so, suspect cam sensor/synchronizer fault or incorrectly installed synchronizer.

4. Unplug the DPFE sensor and see if concern is resolved, if so, suspect shorted DPFE sensor.

5. Check torque converter command during concern, make sure it is not being commanded on during surge.

6. Use lab scope to check crankshaft position signal during concern and ensure the signal is not dropping off.

Mar 27, 2015 | 2007 Ford Taurus

1 Answer

What is location of crankshaft position sensor on 2007 ford f250 with 6.0 diesel.

There are some GREAT pictures I think will help you find it. Go to It is located under the subject of "Camshaft Position Sensor (CMP) wiring pigtail replacement"

Feb 28, 2015 | Ford Cars & Trucks

1 Answer

What will fix codes po320 & po446?

EOBD code Fault location Probable cause
P0320 Crankshaft position WiringCKP/RPM ,
(CKP) sensor/engine sensorECM
speed (RPM) sensor
circuit malfunction
EOBD code Fault location Probable cause P0446 Evaporative emission (EVAP) system, vent control - circuit malfunction Wiring, EVAP canister purge valve, ECM Hope that helps

Oct 19, 2014 | 2007 Ford Explorer Sport Trac

1 Answer

2007 sport trac. What will fix codes po320 &

Faulty Ignition/Distributor engine speed sensor, Faulty Crankshaft Position sensor
Ignition/Distributor engine speed sensor harness is open or shorted, Ignition/Distributor engine speed sensor circuit poor electrical connection, Low battery charge, Faulty Engine Control Module (ECM)
try tightening the fuel cap if not replace it

Oct 19, 2014 | 2007 Ford Explorer Sport Trac

1 Answer

2007 ford f150 problems

Fuel filter.

Camshaft or crankshaft sensor.

Mass air flow or similar sensor dirty.

Air filter dirty.

All are easy to check and replace.

Jul 11, 2014 | 2007 Ford F-150 Harley Davidson

1 Answer

Where is the camshaft postion sensor on the 07 ford edge with the 3.5 v6?

Locate the cam sensor wiring harness from underneath the vehicle at the front of the engine block near the crankshaft pulley.

Read more :

Jun 12, 2014 | 2007 Ford Edge SEL Plus

1 Answer

2001 gran am\ trying to locate collant sensor

If you have the v6 then you will find the coolant temp sendor near the thermostat housing below the throttle body and just toward the front of the vehicle near the coolant bypass pipe. If you have a 4 cylinder then look at the rear of the cylinder head near thermostat.
Good luck.

Nov 23, 2009 | 2002 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides