Question about 1999 Mercedes-Benz CLK

1 Answer

I've replaced the bulb, the passenger side headlight is still out. My feeling is the problem is electrical but I'm not sure.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 23 Answers

Im assuming that you have check the fuses for the headlights and they are good.If your headlight is HID(Hight Intenstiy Discharge Xenon bulb) The headlight assembly will have a balast that might be defective.Deferentiating the Halogen from HID.Halogen will have a yellowish color when you turn on the headlights whereas the HID will have a whitesh to bluesh in color.If your clk320 does have a halogen then its highly probable you have an electrical problem but if its HID then you might want to replace the balast.

Posted on Nov 09, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
txkjun
  • 409 Answers

SOURCE: E300D Headlight Lens installation

First you have to remove the turn signal lamp. There is a plastic release tang that you push one way and pull the turn signal out. Next you have to remove the filler panel below the headlight assy to gain access to the bottom bolt. 2 screws hold the filler in place. There is also a black plastic filler panel that is pinned to the headlight assy remove it. There are 3 or 4  bolts that hold the headlamp assy in place 2 on top 1 on bottom actually it might be 2 on the bottom. (old age memory loss LOL) remove the bolts and remove the headlamp assy. The lens is held in by plastic clips just pry up gently on the locking clips and remove the lens. I hope this helps. It fairly easy and you should be able to DIY. Good luck and thanks for using FixYa!!

Posted on Dec 28, 2008

  • 651 Answers

SOURCE: headlight bulbs in a 1994 Mercedes SL 500

yes

Posted on Jan 06, 2009

  • 43 Answers

SOURCE: how to relace headlight bulb for 99 model clk320

There is a cover on the back of the assembly to access the bulbs. The assembly does not need to come off.

Posted on Mar 31, 2009

  • 1 Answer

SOURCE: Headlight repair on 2003 Mercedes Benz E320

how do you change left low beam bulb on 2003 mercedes e320

Posted on Jan 04, 2010

ginko
  • 19396 Answers

SOURCE: I have a 2002 CLK320 Mercedes coup & I need to

Here part number:

TURN RATE SENSOR / YAW RATE SENSOR
(+) Electronic Stability Program (ESP)

MERCEDES-BENZ A 0005426518



BOSCH 0265005200

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

1 Answer

I have a 2002 Hyundai Accent (UK RHD). I've had a headlight go out, side lights and full beam still work. I've changed the bulb and fuse but its still dim. Ran out of ideas...


Hi ,Check the light bulb,see if its seat in the seats properly 'for earth' and the light terminals for dirts ,grease,or corrosion.clean if needs to.I think its a Earth problems

Dec 17, 2012 | 2002 Hyundai Accent

1 Answer

Headlight fault


You may have blown a fuse, check fuses first then before you try to replace the bulb again check for broken wires or the correct bulb

Oct 25, 2017 | 2008 Kia Pro-ceed 1.6

1 Answer

Removing low beam bulb on 05 subaruoutback


Whether they become damaged in an accident or simply burn out over time, your Subaru Outback's headlights may eventually need to be replaced. Fortunately, once you've purchased the right replacement bulb for your model year, performing the repair yourself is relatively easy. These instructions only apply to Outback models made after 2000.

  1. Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment (driver's side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Turn the bulb cover counterclockwise and remove it from the assembly.

  4. 4

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  5. 5

    Pull the old bulb directly out of the socket and replace it with the new one. Press the retaining spring back into place and reattach the electrical connector.

  6. 6

    Replace the bulb cover, and then turn on the engine. Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

    Replacing the High-Beam Bulbs
  1. 1

    Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment ( drivers side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  4. 4

    Turn the headlight bulb counterclockwise and pull it out of the socket.

  5. 5

    Reinstall the new bulb, replace the retaining spring and reconnect the electrical connector.

  6. 6

    Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

Sep 14, 2012 | Cars & Trucks

2 Answers

2007 yukon headlight wont turn on


Odds are you have a connection problem. Stop & buy a tube of dielectric compound from an auto parts store. Apply it to the electrical connection at the lamp after you make sure there is no corrosion present.

Feb 04, 2018 | 2007 GMC Yukon

1 Answer

Headlight bulb replacement


1) The access to the headlights are in the wheel arches, so first thig to do is turn the wheel into the wheelarch so you have just enough space to take off the cover.

2) This is where you have to work blind as you only have enough room for your arm. Reach into the hole and feel for the large circular cap that covers the back of the bulb holder. It takes a quarter turn (anticlockwise) to come off.

3) Remove the electric connector block that is pushed onto the bulb terminals, and put to one side.

4) The bulb is held in place by a strange W shape spring clip. Try not to remove the whole clip. It is held in place by two circular rings at the base, and clips into a small notch at the top of the mounting. It has two arms that apply pressure to the baseplate of the bulb thereby holding it in place. By moving the top of the clip towards you, it will clear the holding notch and then drop down (still being held in place in the two rings at the bottom).

5) The bulb can how be removed and a new one put in it's place. There is a cut out in the bulbs base plate so that it can seat correctly in the headlight. Once this is in, you need to pull up the clip and then try and catch the top of the clip back in the notch by pulling it slightly towards you and then pushing it forwards to clip in.

6) Push on the electric connector block. An idea at this point is to test the light to see if the connector is on correctly, and that the bulb works.

Replace the plastic circular back of the bulb unit to seal it and you can then refit the wheel arch cover plate.

Step 4 and 5 are the trickiest. Not the easiest thing to do, not sure why Renault couldn't have made it a bit easier, but at least the job can be done without removing whells, bumpers etc that I've seen on other web sites.

Jan 14, 2012 | 2005 Renault Megane Scenic

1 Answer

I've noticed driver side headlight has alot of moisture and 2 light bulbs have burnt out. The passenger side doesn't have as much moisture.


either a tiny hole in the lens or not getting a proper seal around the beam, replace sealed headlight assembly should be $30-35at the local junk yard

Jul 09, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


LIGHTING Headlights REMOVAL & INSTALLATION
  1. Unscrew the Torx retaining screws and remove the headlight bezel.
  2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
  3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

Aug 23, 2009 | 1989 Cadillac Seville

2 Answers

Lightbulb driver side 2008gmc 3500 6.6l


how to change driver side headlight bulbs?

May 30, 2009 | 2008 GMC Sierra 3500HD 2WD

Not finding what you are looking for?
1999 Mercedes-Benz CLK Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...