Question about 2004 Isuzu Rodeo

Open Question

Remove glove box on 2003 isuzu rodeo - 2004 Isuzu Rodeo

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: how to change oil transmission isuzu rodeo 2003

There are two drain plugs on the bottom of the pan. remove the lower one to drain the trans fluid. To refill, use a pump and pump the fluid into the upper drain plug until it seeps out and re-install the plug, similar to refilling a manual trans.
Once this is done, Start the vehicle and run it for about 3 minutes, shifting through all gears (do not drive vehicle Remove the upper drain plug and let any excess fluid drain out. Done. This is as per Mitchell OnDemand.

Posted on Aug 14, 2008

zolo6321
  • 7 Answers

SOURCE: 99 Isuzu Rodeo 3.2L 2wd Catalytic Converter instructions

you're having the same problem i had with my 99 isuzu rodeo 2 wd 3.2 i paid a muffler guy over $600 to replace those catalytic converters, if you're good at welding you could do the welding yourself after buying the catalytics, basiclly i seen them just cut them off and welded them back on

Posted on Dec 31, 2008

  • 1779 Answers

SOURCE: 95 isuzu rodeo ignition lock cyl removal

Great to hear the update, and that the car is up and running. Good luck with it,
Curt

Posted on Apr 09, 2009

  • 2 Answers

SOURCE: Remove and replace side mirror

take off inside panel of door...there are 3 nuts holding the mirror on...simply remove the 3 nuts and replace....pay attention to the brittleness of the inside panel....be gentle

Posted on Aug 09, 2009

emissionwiz
  • 75117 Answers

SOURCE: 2001 rodeo won't start. the solenoid on the

the clicking is the start relay which u don't hear unless the starter doesn't work, u have a defective starter solenoid, the internal contacts are burned, this is a NipponDenso style starter and they all have this same problem, u can replace the starter, replace the starter solenoid or replace the copper contacts in side the solenoid for around $12.00 USD

Posted on Feb 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

/how-to-remove-glove-box-from-a-2002-isuzu-rodeo


we just look first
did you.
if you see screw,there we off the.
if not its got the magic bind sides to let it drop down trick.
some need that done first to get to hinge screws.
see>?
just look and you will figure it out.
its not magic its only box with hinge.

Jan 19, 2017 | 2002 Isuzu Rodeo

1 Answer

Fuel pump fuse hot in fuse box under hood and fuel pump doesn't go on


most likely a fuel pump that has taken a dump. isuzu uses typical crappy gm/ac delco/dephi parts. you would need to drop the fuel tank to replace the fuel pump.

Sep 22, 2014 | 2003 Isuzu Rodeo

1 Answer

Panel cover 1991 isuzu rodeo


in what country?
its and old car.? and very few wreckers have them.
why not just get the photo of one, and keep it in glove box.
for fuse ID or the used operators guide off ebay.
???

Jul 10, 2014 | 1991 Isuzu Rodeo

1 Answer

Where is the heater and ac blower for a 1997 isuzu rodeo?


Under glove box, facing up. 4 brass screws hold it in and has a wire connector plugged in the side.

Jan 11, 2012 | 1997 Isuzu Rodeo

1 Answer

Where is the blower motor located on a 97 rodeo


Hi, the blower motor is located behind the glove box or compartment.
  • Remove floor distribution ducts and glove box, as necessary to gain access to motor.
  • Disconnect electrical connector from blower motor.
  • Remove screws securing motor mounting plate to housing, then the motor assembly, taking care not to damage seal.
  • Remove retaining ring securing impeller, then the impeller.
  • Reverse procedure to install

May 27, 2011 | 1997 Isuzu Rodeo

1 Answer

How to remove a\c evap coil from 2001 isuzu rodeo


You can try accessing it from behind the glovebox assembly, depending on the engine/trim combination you have, but you may have to pull the dash out, after evacuating the system with an A/C Recovery system. The Evap coil is located against the interior side of the firewall.

The glove box should come out by removing the two retaining plugs at the interior side of the box assembly, and then the frame screws along the top.

Jun 06, 2010 | 2004 Isuzu Rodeo

2 Answers

How do i change the ac/heater blower motor in 96 isuzu rodeo?


I assumed it's a v6
you need to remove the glove box compartment
remove the screws on the blower motor housing
remove the motor

Feb 26, 2010 | 1996 Isuzu Rodeo

1 Answer

Blower Motor Resistor for front AC/Heater


remove glove box....its in the casing near motor.....2 screws and 1 connector

Jan 19, 2009 | 2004 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...