Question about Cars & Trucks

Open Question

Po 441 code on 2007 hyundai gls - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: PO 441 PO 141 AND PO 137 HYUNDAI ELANTRA 1999.

It sounds like you've broken the exaust sensor that near the mainfold.

Posted on Jun 07, 2009

  • 184 Answers

SOURCE: 2003 Hyundai Elantra GLS. Check engine light, code PO133

Did you use a aftermarket O2 sensor or a genuine Hyundai one? If it's an aftermarket one it may be bad or not as good as the OEM one. See here for more details and other potential causes: P0133

Posted on Feb 11, 2010

ZJLimited
  • 17970 Answers

SOURCE: need fil for error code P2626 Hyundai Elantra GLS

P2626 O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 Sensor 1)

I'll sure this has to do with a faulty O2 sensor. This sensor is usually located around the header of your car, or down more on your exhaust.

Try disconnecting your battery for 30 mins, hook it back up, and start your car again. This will erase the error. See if it comes in again.

Hope this help (remember rated this post).

Posted on Mar 25, 2010

  • 1 Answer

SOURCE: po 441 code on a 04 dodge dakota

the purge solenoid is right next to the battery and has 2 hoses one going to the front of the intake/throttle and one going to the canister under the driver side door and most likely isnt the problem i replaced mine spent 40 bucks and didnt solve the problem

Posted on Apr 28, 2010

  • 16 Answers

SOURCE: Hav Check eng. Light Code

P0441 Evaporative Emission Control System Incorrect Purge Flow

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tankmag-glass_10x10.gif into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
FB.init("dd7d9e9681341cde77587bc6a2029f6f");OBD-Codes.com on Facebook Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM
Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Common Chrysler fix - Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM

Posted on Sep 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

PO-139 I had that sensor change 3 weeks ago and the check engine light came on again this morning.Thanks


Probably replaced a good sensor. This codes could be from a bad sensor, a vacuum leak, or an exhaust leak before the sensor.

Dec 01, 2015 | 2006 Hyundai Tucson

1 Answer

2000 Elantra GLS with PO 732 and PO 734 codes. Any hope of a repair without a complete tranny rebuild?


2nd and 4th gear ratio codes. No matter the cause, the transmission has to be pulled. Low end at a garage is $1000, top end $2500+.

Mar 05, 2015 | 2000 Hyundai Elantra GLS

1 Answer

Code po 441 2004 Kia


Check the fuel cap or vent valve if you have a smoke machine you can close vent valve with a bi directional scanner and smoke the system if leak appears though charcol canister with vent valve close the vent valve is the problem.
Fuel tank should have a certain amount of vac in hg that is monitered by pcm of vac is low or has none the it will trigger check engine light on 2nd ignition cycle

Jan 22, 2015 | Kia Cars & Trucks

1 Answer

Code po 341


Cam sensor circuit issue.

Jan 16, 2015 | 2013 Hyundai Elantra GLS

1 Answer

PO 441


This is a incorrect purge flow code, try replacing the purge vsv located on the hose that has the green valve cap on it, one hose has vacuum when the engine is running the other hose goes back to the fuel tank, the valve has an electrical connector on it .

May 15, 2014 | 2007 Toyota Camry

2 Answers

Po 171, po 305, po 441


Hi, I know from my past experiances the spark plug wires at the boot ends than slide onto the sparkplugs usually over time short out due to the metal tubes that protect the sparkplugs from heat kind of ark across from the metal tube through the plug boot causing an error code. Sometimes in the dark you can actually see them arking at the tube on the engine, and also hear a crackling noise. As to the code for the O2 sensor that's a normal wear and tear item that may need replaced. As all vehicle age over time electrical connections, and things have issues develop and cause havick with sensors and computers in these vehicles too.


As with the 441 code and then the other code for the O2 sensor showing up may mean both O2 sensors are going bad if your system has 2 sensors in the exhaust, usually one before the cat converter and one behind it. A lot of this also is due to what gasoline you use in the vehicle over time. Lower octane gas may be what is causing things to act up.

Jan 03, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Dodge durango po 441


P0441 indicates incorrect purge flow. You could have a problem with the purge valve, cannister, and/or vacuum lines.

Mar 07, 2012 | Dodge Durango Cars & Trucks

1 Answer

What is the most common cause of an error code: 0040 and 0041 in a 2003 dodge ram 1500?


no such codes, it would be something like a po 441 or po 045. recheck your codes,good luck.

Oct 28, 2009 | 2004 Dodge Ram 1500

1 Answer

PO 441 evaporative Emission controle system


Possible causes
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve

Apr 18, 2009 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...