Question about 1997 Honda Accord

Open Question

Honda accord p1491 error code - 1997 Honda Accord

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

skidoorev
  • 11 Answers

SOURCE: error code 41 on 1994 honda accord

A 41 error is your throttle positioning sensor, its a electrical sensor hooked to your injectors telling them how much gas/air to be releasing as u accelerate/deccelerate. Best and only way to fix it is to buy a new sensor. Then reset the cars computer at a diagnostics shop for little or no cost.

Posted on Mar 22, 2009

EnginEar
  • 57 Answers

SOURCE: I HAVE A P1491 CODE ON MY 1998 HONDA ACCORD ERG

Code P1491 is EGR lift insufficient. It is usually accompanied by P0401. If you have a v6 Accord, there was a recall for the EGR port plugging. Check with your Honda dealer to see if your car is covered under that recall. If you have a 4 cyl, plan on replaceing the EGR. In addition, you need to clean the ports in the engine on the intake and exhaust sides of the EGR ports. To do this, spray some carb/choke//intake cleaner into the ports to saturate the black exhaust build-up. Later, jam a coat hanger or spare dipstick (or some long flexible metal rod) into the parts to break up the black deposits. When your rod passes through easily, spray more cleaner to pass it through. Reassemble and start the engine. It will run rough at first, so you need to give it gas pedal input to burn off the carb cleaner. You should be good to go.

Posted on May 26, 2009

philschneide
  • 448 Answers

SOURCE: 1998 Honda Accord EX V6 2 Door - Radio Error Code on Display

No-one is ever particularly happy to here this, but this is the way it is; we do have to keep in mind that the original idea of codes on radios was to prevent people who steal them from being able to use them.

So, if an audio unit with theft protection is disconnected from electrical power, you must enter a unique code number into the unit or it will not work. This code and the audio unit’s serial number are listed on the anti-theft ID card that comes with the vehicle. If this card is lost, you must obtain the audio unit serial number in order to get the radio code (some people say that they have found the code on a sticker inside the glove compartment, but I wouldn’t count on that). Some newer vehicles allow you to retrieve the audio unit serial number electronically from the radio. Refer to your owner’s manual for the specific procedure (the following usually will work: Turn the radio off. Push the preset 1, preset 6, and power buttons at the same time, then quickly release. The serial number will come up in two sets of numbers.)
Some older vehicles (model year 2003 and older) require a visit to the dealer in order to retrieve the audio unit serial number (or you can remove the unit and get the serial number from the back of the radio). Once you have the audio unit serial number, you can call Auto Customer Service at (800) 999-1009 or have the dealer look up the radio code.

Here is the URL for the Honda Owner page. If you register (no charge) you are able to get radio codes using the VIN number of your car, the serial number of your radio, and the
Phone Number and Zip Code that you give them when you register.

https://www.ahm-ownerlink.com/login.asp?page=%2Fprod%5Fhome%2Easp

Hope this helps you with the process.

Posted on Jan 04, 2010

kirkx
  • 2019 Answers

SOURCE: Honda Accord and I have a error code on radio.

If you did not get the radio code written down in the owner's manual when it was installed, as you should have, then you will have to take it to a place that sells that type of radio, and have it reset. It takes a tool only they have, and they don't charge for resetting the code. But then write it down, because it will happen again.

Posted on Feb 07, 2010

  • 2 Answers

SOURCE: 2008 honda accord stereo code error 4

I just changed the battery in my 08 accord same thing there is a code on the left side of glove box.type that code in using the preset numbers it will be on white sticker

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just got my car scanned and a few codes pop up


Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .


Apr 30, 2013 | 2004 Honda Civic

2 Answers

CHECK ENGINE LIGHT ON.


remove the EGR valve and clean the carbon from the port it is connected to, they are known to get clogged up, you may also have a bad egr valve.

Oct 25, 2012 | 2000 Honda Accord

1 Answer

P1491


P1491 EGR Valve Lift Insufficient Detected.Egr may need replacing.

Oct 25, 2012 | 2000 Honda Accord

1 Answer

I am getting a little drag in my pick up speed. I had the code read and it came back as P1491. Is that a bad spark plug?


My 1990 Honda accord does the same thing.Found out the Distributor cap was off set.Now it's stalling before a light replacing a throttle position sensor good luck.

Jul 13, 2012 | 1991 Honda Accord

1 Answer

My car turns off when i start slowing down or when im pressing on the break, i tested it and it gave me 2 numbers a P1491 and a P1456 my car is a 99 honda accord ex, a 4 door.


P1491 = Exhaust Gas Recirculation (EGR) Valve insufficient lift.

P1456 = Evaporative emissions (EVAP) control system leakage (fuel tank system).

Check the EGR valve for a failed vacuum diaphragm. Check the fuel filler cap to make sure it is the correct factory style, has a good check valve and is on tight.

Feb 26, 2011 | 1999 Honda Accord

1 Answer

What is DTC code P1491? 1997 Honda Accord


hi, "EGR Valve Lift Insufficient Detected" is most often caused by a broken vacuum line going to the EGR valve. So I would check all the vaccum lines to be sure they are tight and not broken.If the vacuum lines are good, you will need to check the electronics that operate the EGR system. thanks

Oct 26, 2010 | 1997 Honda Accord

1 Answer

T0113- t0141-To720-t1491 these are the codes to the problems of my 97 honda accord can u please tell me what the problem is read the code for me thank u


do you mean p....
there is only 4 letters for the first code numbers they are:
B,C,P,an U

p0113
intake air temperature circuit,high imput
p0141
02 sensor heater circuit malfunction (bank 1,sensor 2)
p0720
output speed sensor malfunction
p1491
is a enhanced code for honda
Exhaust gas recirulation (EGR)valve insufficient

)

Aug 25, 2010 | Honda Accord Cars & Trucks

2 Answers

I HAVE A P1491 CODE ON MY 1998 HONDA ACCORD ERG


Code P1491 is EGR lift insufficient. It is usually accompanied by P0401. If you have a v6 Accord, there was a recall for the EGR port plugging. Check with your Honda dealer to see if your car is covered under that recall. If you have a 4 cyl, plan on replaceing the EGR. In addition, you need to clean the ports in the engine on the intake and exhaust sides of the EGR ports. To do this, spray some carb/choke//intake cleaner into the ports to saturate the black exhaust build-up. Later, jam a coat hanger or spare dipstick (or some long flexible metal rod) into the parts to break up the black deposits. When your rod passes through easily, spray more cleaner to pass it through. Reassemble and start the engine. It will run rough at first, so you need to give it gas pedal input to burn off the carb cleaner. You should be good to go.

Nov 23, 2008 | 1998 Honda Accord

Not finding what you are looking for?
1997 Honda Accord Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...