Question about 1992 Oldsmobile Cutlass Ciera

1 Answer

Cannot remove the pulley from my 1991 olds cutlass ciera 's water pump. Its a 4cyl. Plus the new water pump doesn't look quite the same.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 114 Answers

I replaced my water pump on my 92 olds, and the pulley will look slightly different because it's newer, but just make sure its the right one. The pulley does not come off of the water pump, both the water pump and pulley have to be changed. Your new one should come with both the pump and pulley already connected

Posted on Jan 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i remove the power steering pully and pump for a 92 olds cutlass s?

As far as the pulley, If you get a new pump from a national brand auto store, the new pump may not have a pulley, the store will remove the pulley and install on new pump for you. To remove the pump, take belt off. Remove lines from pump, The return line should be low pressure, probably just hose clamp needs to be loosened. The high pressure line is a threaded fitting, have to use wrench to get it loose. If your going to work on your own vehicles, you need a basic set of tools, as far as wrenches and sockets, standard and metric sizes.
Find mounting bolts for pump, take them loose.
I looked at info for cutlass ciera S, 3.3L engine. Click on the comment link.

Oct 20, 2016 | Cars & Trucks

1 Answer

Water leaking

Water Pump has gone out.
assuming that you have the 2.5L TBI OHV 4cyl these should run you about $35.

Feb 07, 2013 | 1991 Oldsmobile Cutlass Ciera

1 Answer

How do you take the pump out of a 1991 Cutlass Ciera ?

To replace the fuel pump requires the fuel pump be removed from the car, this requires a helper and floor jack

Feb 04, 2011 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Antifrezz is leaking from the engine no hoses are broke whers is it coming from

If all your hose and hose clamps are good. There is a good chance that the water pump has to be replaced, once the water pump bearing is worn. The coolant will leak from the weep hole on the water pump when the engine is running and the only way to stop the leak is to replace the water pump.
Thank you for using fixya.
Depending on engine size a 3.1 liter v6 and a 2.2 **** 4cyl. are both located in the front of the engine.
Remove serpentine belt,remove 4 10mm from pulley (v6)(three 13mm for 4cyl.)remove pulley.v6 will have 6 8mm bolts,4cyl. will have 4 13mm bolts-remove clean surfaces install new pump.
About 40 mins.v6,60mins for 4cyl. Be sure to drain coolant before you start, refill whith proper coolant, some 95 up gm require dexcool anti freeze (orange in color).

Apr 16, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Water pump installation

1. Remove acces. drive belt
2. loosen hose(s) attached to pump.
3. loosen bolts that hold on pump.
4. remove pump. If your pulley is pressed on, take to parts store and have them romve it for you.
5. clean surface and use the gasket to replace new pump. If you dont have a gasket(depending on your year), use rtv sealant and reverse the process to install. Good luck

Dec 11, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Antifreeze leaking just underneath the pulley

Your water pump is defective and needs replacing if you see it leaking at the water pump pulley. The bearing has gone bad.

Nov 28, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

I have no idea how to remove the water pump pulley!

Ok, now I know for sure what the problem is, the water pump pulley is pressed on, u will need to disconnect the top side engine mount and raise the engine up about a foot with a floor jack, make sure u put the jack saddle somewhere where u won't damage the oil pan, if u must lift it by the pan use a flat peice of wood to spread the load, once it is up the pump will slide out, then u must have the old pulley removed and the new one pressed on,I think a power steering pulley remover tool is what u need, Kragen and Autozone will loan these to u free of charge if u want to try and press the pulley off and on yourself.

Jan 05, 2009 | 1991 Oldsmobile Cutlass Ciera

3 Answers

1991 olds wont start

I have no spark. Changed the CSS and still no spark. I also changed the Coil packs with a junk yard 1. Does anything else control spark other then ECM?

Dec 18, 2008 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides