Question about Cars & Trucks

Open Question

Were is the knock sensor located on a 2008 ford expedition

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 27 Answers

SOURCE: Oxygen Sensor Location 2001 Ford Expedition Eddie Bauer

There are four o2 sensors on this truck. one on each side just below the exhaust manifold, and one on each side behind the second catalytic converters. (just about even with the back of the front doors.

Posted on Jun 18, 2008

Ad
  • 1 Answer

SOURCE: 2003 FORD EXPEDITION PCV VALVE LOCATION

show me a picture. everyone else says it's on the passenger side. nothing white on driver side of my 03 expedition.

Posted on Mar 07, 2009

  • 6 Answers

SOURCE: 1999 FORD EXPEDITION VEHICLE SPEED SENSOR

It should be on the back of the transmission near where the driveshaft goes in. Buy a new one, jack up your truck and look for the old one on the back of the transmission

Posted on Apr 03, 2009

  • 218 Answers

SOURCE: expedition knock sensor

NO.U HAVE TO REMOVE THE UPPER INTAKE

Posted on May 14, 2009

chuck943
  • 783 Answers

SOURCE: location of CHT sensor

It is located at the back of the passenger side cylinder head close to where the intake manifold and head meet.It will have a YE/LG and GY/RD wires to it.

Posted on May 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the coolent sensor on 5.4l ford expedition 2005


On some vehicles, the coolent sensor is located inside bottom of the coolant fill tank located by the fender. It should have a tube going to the radiator.

Jul 01, 2014 | 2008 Skoda Octavia 1.9

2 Answers

Knock sensor location


Knock sensor is located on the cylinder block between no. 1 and 2 cylinder.

May 10, 2014 | 2008 Hyundai Sonata 3.3

1 Answer

Location of air suspension compressor in a 2008 ford expedition


trent, check underneath the washer fluid resevoir or just a few inches towards the front.

Nov 24, 2013 | 2008 Ford Expedition Eddie

1 Answer

Locating the knock sensor on a 1998 ford expedition


It is under the intake manifold see picture below, it is the green part in center of engine valley between the heads.
11_5_2012_11_38_19_pm.jpg

Nov 05, 2012 | 1998 Ford Expedition

1 Answer

Can I replace the knock sensor on a 1999 ford expedition Myself and if so what is the location


Yes you should be able to do this yourself. The part at autozone is about 42 bucks. The knock sensor is located on the right side of the engine block under the exhuast manifold on the V6. It should also be in the same general area on a V8.

Jul 25, 2011 | Ford Expedition Cars & Trucks

1 Answer

Where is the in line fuel filter located on a 2008 ford expedition 5.4 liter


FUEL FILTER LOCATION IS MOUNTED ALONG THE UNDER VECHICLE FRAME RAIL.

Mar 06, 2011 | 2008 Ford Expedition

1 Answer

Need to know how to install knock sensors and where they are need diagram. 2005 expedition 5.4 engine


Hello adamjerkins,

It is somewhat complicated to change the knock sensors. There are two of them and they are located under the intake manifold. The intake manifold must be removed. I would recommend tha you replace both while you have the engine apart.

What leads you to believe the knock sensors are bad, I've seen few bad knock sensors? The knock sensor issues more times than not have been caused by other problems.

After you remove the intake manifold disconnect the knock sensor connectors. Remove the bolts and the two knock sensors then replace with new knock sensors tighten the bolts to 15 foot pounds. Reinstall manifold. The total job for an experienced mechanic with tools is about 5 hours. Not a good job for a beginner.


Regards,
netvan

Mar 05, 2011 | 2005 Ford Expedition

1 Answer

Why is the right side of my engine on my 2003 ford expedition knocking?


How do you know it is the right side?
How do you know it is ,in fact knocking

Do you have a Knock Sensor Code set?

V6 or V8

May 12, 2010 | 2003 Ford Expedition

1 Answer

Expedition knock sensor


NO.U HAVE TO REMOVE THE UPPER INTAKE

May 14, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...