Question about Cars & Trucks

Open Question

How to reset timing belt light on 2009 toyota hiace

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: How to reset timing belt light

to reset the light you need to remove speedo dash assembly ,on the back of the printed curcuit there is a small screw and a hole next to it remove screw and fit to empty hole . refit assembly

Posted on May 07, 2009

Ad
  • 1 Answer

SOURCE: Timing belt light of Toyota LandCruiser 2006

the reset procedure of the timing belt light is all done by pressing the trip meter button and holding it in whilst the ignition is turned to on then select from the trip button then continue pressing until you come to 15 on trip metre, turn off and then restart. The light should then go off.

Posted on Jan 13, 2010

  • 4 Answers

SOURCE: my timing belt light comes and i need to reset the

You need to remove the dash first, then remove the speedo /guage cluster unit from the vehicle, by undoing the 3 or 4 plugs on the back of the cluster unit. when you look at the back of the unit you will see alot of srews and wires. look closely around the middle part and you will notice a small phillips screw with a empty hole next to it. remove the srew and put it back into the empty hole which was next to it. This resets the timing belt lamp. good luck

Posted on Aug 03, 2010

  • 184 Answers

SOURCE: how to reset timing belt

usually 2 options to reset toyota light.
1.remove small rubber plug in dash clear lense.use a long thin rod to reach in and push the small reset button at the bottom of the gauges.Light will extinguish.
2.remove the instrument panel and unplug all from behind to turn it over.Usually in the centre of the rear you will see two holes and 1 screw.for t-belt.shift the screw to other hole.refit dash ensuring all the plugs are refitted.Light should now be out.

Posted on Apr 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset timing belt light of 2kd-ftv hiace 2006 model


that's funny, (skipping the job?>)
plug in scan tool hit reset! (best of best)
find all ECU fuse, pull them, it resets
pull battery neg lug, and this works but kills radio codes,(bricks it) and kills NAV option with same reasons.

in most cars there is a chapter in the operators guide
called resettiing service codes, did you read that yet.

Jan 16, 2015 | 2007 Toyota Hi-Ace 220

2 Answers

Where can I download a free toyota hiace 2.7 petrol 2009 owners manual?


Just google free manual for your model, make sure you put all model specs.

Jan 11, 2015 | 2007 Toyota Hi-Ace 220

1 Answer

How do i reset the timing belt light for 2005 toyota hiace with analog speedo?


The computer probably needs to reset to clear the code. Best way is go to Auto Zone or Advance Auto and ask them to reset the comupter. It can be done by disconnecting the negative battery cable from the battery, but then you may have problems with the security system, and you can loose stored info in your radio, etc.So I suggest you have the computer cleared of codes.

May 19, 2014 | 1999 Toyota Land Cruiser

1 Answer

Serpentine belt wont go back on. 2009 toyota hiace


If you have let off the adjuster idler pulley then the reason the belt will not fit is the way you are trying to put it on. You will need a diagram but generally the belt goes over flat pulleys on the back of the belt and around pulleys with teeth. It will be the way you are pitting it on

Oct 03, 2013 | 1991 Buick Park Avenue

1 Answer

How to reset timing belt warning light on toyota hiace LH 172 model engine in electronic meter


I have a toyota hiace 172 van.There is 5L engine and digital counter speed mete . there km reading are very high.So need to me reduce.Please how to do this?

Mar 13, 2013 | Cars & Trucks

1 Answer

Reset dpd light on toyota hiace


in hiace kdh201 have 5 pin socket under the left hand side in dash panel. find it and red/yellow wire connect with ground after 2s it will start to flushing ,some time it want to more than one flushing to clean DPF filter.be careful because this white smoke cause to censers and don't operate A/C ,headlight,and accelerate position .it will stop your DPF cleaning process.good luck

Aug 19, 2012 | Toyota HiAce Cars & Trucks

3 Answers

Toyota hilux d4d 3.0 litre fuel system light reset ?


Remove the key from the ignition but keep it handy. Important: Disconnect the negative terminal of the battery for longer than 90 seconds to prevent the risk of having the airbags deploy! Replace the diesel filter (Follow the instructions that can be found in Toyota service manuals (search www). Remove the diesel filter sensor cable (the one on top of the filter assembly). Make sure the new O-rings seat properly. Close the filter assembly by turning the locking ring until it clicks. Bleed the filter assembly by pushing the little plunger thing on the top of the assembly until pumping becomes difficult. Connect the negative back onto the battery. Insert the key in the lock and turn until the dashboard warning lamps come on, but do not start the car yet. Within 3 to 60 seconds of doing this re-connect the diesel flter sensor cable. The light should be extinguished. Obviously there could be another problem causing the light to remain on (not flashing - steady on). If the light is flashing, then you have water in the system and should follow the answer supplied elsewhere by someone else to drain the water. Now start the car and enjoy clean diesel fuel driving. You should really not wait for the light to come on steady before chnaging the filter. Some fanatics believe every 10,000km is the longest you should wait, but this depends on fuel quality, low or high sulfur content, etc. Rather do it more frequently than having to buy new injectors.

Apr 10, 2012 | 2007 Toyota Hilux 2.7

3 Answers

How to reset timing belt warning light after 150,000 km on toyota hiace 2kd-ftv engine


if it has a digital odo/ press trip knob until odo is displayed/ press and hold , turn ignition , hold for 4 secounds , release and press again, number 10 will be displayed, keep pressing until 20 comes up, press until odo reading is displayed again, turn ignition off , turn on again , notice the t belt lamp turn off in appros 5 secounds / if not able to reset try this again

Apr 02, 2011 | 2007 Toyota 4Runner

1 Answer

My timing belt light comes and i need to reset the light it have a degital speedmeter. How do i reset the timing belt light ? It is a toyota hiace.


You need to remove the dash first, then remove the speedo /guage cluster unit from the vehicle, by undoing the 3 or 4 plugs on the back of the cluster unit. when you look at the back of the unit you will see alot of srews and wires. look closely around the middle part and you will notice a small phillips screw with a empty hole next to it. remove the srew and put it back into the empty hole which was next to it. This resets the timing belt lamp. good luck

Jun 30, 2010 | 1999 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...