Question about 2002 Jeep Liberty
What fuse is for the rear window actuator on my 2002 Jeep Liberty Sport?
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from
Posted on Mar 01, 2009
Replace rear rotors on 04 liberty.
Remove tire & wheel
Remove brake caliper, tie up out of way.
Back off e-brake shoe adjustment.
Remove factory spring clip from lugs (2places)
This is the crude part....
After attempting to pull off disc/drum with puller....I got pretty sick of it. Understand this is in the Northeast with lots of salt on the roads in winter. Needless to say there is a ridge of rust around the inside edge of the e-brake surface. Any more pressure and I was afraid of damage to the e-brake shoe asembly. I then took a small grinder with a cut off wheel and cut the disc thru (used space where caliper usually sits). Also cut nearly through the face between 2 lugs. You can't quite get thru the back corner at the disc. Since the material is cast iron it will crack when you drive a wedge in the slot cut in the disc. This opens the housing around the shoes and it slides off easily. The cutting operation took less than10 mins, alot less than the puller with hammer assist!
I know this is a bit "unorthodox" to say the least, however the object is to remove the old junk disc safely and as quickly as possible, without harming the e-brake parts inside.
Install new parts in reverse order, new pads go in easy after squeezing the caliper piston back with a c clamp as is the normal procedure.
Posted on Mar 22, 2009
Use a #20 Torx screwdriver to remove two screws located on the inner side tail light assembly w/ trunk open.Pull taillight assembly straight back from the vehicle to get it off. You may need to utilize a wedge to gently work the top and bottom of assembly away from vehicle on outer side. If so, be careful to use a protective layer (such as a thin piece of cardboard) next to the body to prevent scratching the paint. A wooden kitchen spatula works with out scratching.Once removed, twist applicable light cover counter clockwise and pull to access lightbulb.You may want to apply a small amount of lithium grease to the two plastic stud holes before reinstalling the cover to make it easier to remove the next time.
Posted on Jul 09, 2009
1-20amp-pwr outlet frt. 2-10amp-rear fog lights(export only)
3-15 amp-horn 4-10amp-hedlt low beam rt
5-10amp-hedlt low beam lft 6-20amp-bodycontrolmodule/pwr dr locks 7-spare 8-spare 9-10amp- rt pk lt /rt tail lt/trailer tow lt/cluster
10-spare 11-15 amp-flasher 12-15 amp-stop lts
15-10amp-pdc fuel pmp & auto shutdownrelays/skis
16-20amp-pwr outlet rear 17-15amp-rear wiper 18-20amp-radio choke relay 19-20amp-frt fog lts/trailer tow stop and turn lts
20-20amp-sunroof 21-spare 22-10amp-wiperswitch/frt and rear washer 23-10amp-lft park lt/lft tail lt 24-10amp-pdc blower motor relay 25-10amp-heatseatswitch/hvac controlhead/trailor tow battery charge 26-10amp-hedlt highbeam rt 27-10amp-hedlt highbeam lft
28-spare 29-15amp-heated seat module 30-10amp-heated mirrors/rearwindowdefrosterindicator 31-20amp-cigarlighter
33-10amp-skis/diagnostic connector 34-15amp-cluster/courtesy lts/radio/bodycontrolmodule/maplights/cmtc/underhood lt/vanity lts
35-spare 36-10amp-ignition run/start-orc/lft and rt siacm
37-10amp-ignition run only-orc 38-10amp-abs module/brake shift interlock solenoid 39-10amp-rear window defroster relay/flasher/backup lts
Posted on Jul 10, 2009
SOURCE: how to replace radiator in
Disconnect the negative battery cable at battery.
Drain coolant from radiator
Remove the front grill .
Remove the cooling fan from the engine, if equipped.
Remove the two radiator mounting bolts.
Disconnect both transmission cooler lines from radiator.
Disconnect the connector for the electric fan.
Disconnect the power steering cooler line from cooler.
Disconnect the radiator upper and lower hoses.
Disconnect the overflow hose from radiator.
The lower part of radiator is equipped with two alignment dowel pins. They are located on the bottom of radiator tank and fit into rubber grommets. These rubber grommets are pressed into the radiator lower crossmember.
Posted on Jul 31, 2011
Tips for a great answer:
Nov 01, 2015 | 2005 Jeep Liberty Sport
Jun 26, 2014 | 2007 Jeep Liberty Sport
Sep 12, 2010 | 2002 Jeep Liberty
Feb 17, 2010 | 2002 Jeep Liberty
Feb 04, 2010 | 2002 Jeep Liberty
Sep 11, 2009 | 2002 Jeep Liberty
Sep 04, 2009 | 2002 Jeep Liberty
Jun 13, 2009 | 2002 Jeep Liberty
26 people viewed this question
Usually answered in minutes!