Question about 1998 Mitsubishi Mirage

1 Answer

Removing drivers side paneling?

Is there any special way to do it? I have taken the window crank off and i have unscrewed the screw that keeps it on tight. But are there clips or something else?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes there are little clips on the inside that just pop into place.. Sounds like all you have left to do is take out the screw that holds in the door handle.. its a small one near the top of the casing behind the actual handle itself.. once that is off slip a screwdriver under a part of the panel so you can get a grip and pull hard.. it should just pop right off.. and it will pop right back into place just as easy..

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i repalce the power window switch on the drivers side of a 2004 Kia Sorento


REMOVE DOOR PANEL USING SPECIAL TRIM REMOVAL TOOL. (PLASTIC CLIPS). PEEL BACK ICE & WATER PLASTIC COVERING IF NECESSARY. REMOVE ANY AND ALL SCREWS SECURING ANYTHING TO DOOR PANEL, IE: TRIM, HANDLES, ETC.WINDOW AND POWER LOCK SWITCH SHOULD NOW BE ACCESSIBLE. UNCLIP, AND/OR UNSCREW SWITCH. DETACH ELECTRICAL LEAD FROM SWITCH. INSTALL ALL COMPONENTS IN REVERSE ORDER

Jan 21, 2015 | 2004 Kia Sorento

1 Answer

Remove citroen c3 rear door panel


Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.
Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.
Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.
Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.
Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.
Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.
Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.
Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.
GM Tech2 GM Diagnostic Scanner with 32MB Card and TIS2000

Oct 10, 2014 | 2006 Citroen C3 1.4i

1 Answer

How do you remove passenger sliding door handle on oldsmobile silhouitte


The process of removing car door panels is essentially the same for each make of car. You may need to remove these panels when your fixing locks or power windows, replacing window cranks, installing speakers or replacing the side mirrors. Learning how to remove the panels yourself can save money on simple car repairs.
Related Searches:

Difficulty: Moderately EasyInstructionsThings You'll Need
  • Set of screwdrivers
  • L pick
  • Small flashlight
  • Ratchet and socket
    • 1

      Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.

    • 2

      Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.

    • 3

      Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.

    • 4

      Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.

    • 5

      Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.

    • 6

      Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.

    • 7

      Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.

    • 8

      Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.

Jan 10, 2012 | 1998 Oldsmobile Silhouette

1 Answer

How do I remove window crank handle on 1990 gmc manual window


the best way of doing it with out a special tool is to take a large flat handled screw driver and wedge it between the base of the crank and the door panel making shure you also make shure the black plastic spacer is on the side of the door panel so the clip on the crank is exposed turn the handle to align the clip as desired and use a hooked device or even a small screw driver to pop the retaining clip out..simple...make shure you reinstall the clip back on the crank handle before putting it back on..and then just press it on with a tap from your hand...

Apr 22, 2011 | 2004 GMC Sierra 2500

1 Answer

How too remove door panel and window crank handle on driver side on 2001 chevy van


On that model of van, you will have to remove the screws on the lower side of the panel, and in the door handle. The window crank handle has a spring clip in it that takes a special tool that is available at any parts store, but very easy to use (you just slide it up and down inside of the handle a few times, and it should pop off). After you have the screws, and handle off, you will need to "pop" the panel loose from the door. whille pulling on the sides of the panel, look inside of the panel to see if you can locate the pop in fasteners. When located, you'll have to have a screw driver, or similar object to pry the panel off of the door. (some of the fasteners might break, but are available at the part store) After the panel is loose, be careful of the door release handle, and with the window in the down position, take all of the switches loose from the panel and carefully raise the panel up and out.I hope that this is helpfull.

Jan 03, 2011 | 1999 Chevrolet Express

1 Answer

How do I remove driver side door window


You need to remove inner door panel by unscrewing the screws on inner door handle and take a flat screw driver wedge it between the panel and door use flash light to see the clips along the sides and lower part of door and pry them free. then look through the inner door cut outs to find window track. Once you see it use ratchet or screw driver and loosen the window free form track. Then carefully remove window.

Apr 01, 2010 | 2003 Mazda MPV

1 Answer

How to replace driver side window 97 4 door honda civic


normally on the honda2.gif models there are two screws that need to be taken out, the inside latch area (plastic cap covering it) and the door pull (normally down in the bottom covered with a plastic cap), thin small flat blade will work to remove. once the is done you will need to pull out the latch area on the driver's window control panel, disconnect the connectors. set the aside, next you will need a thin flat blade screw driver or flat pry bay, start at the bottom of the door to pry out the panel, check for screws, if you cannot see any proceed to using the flat blade to remove the panel (will make a loud snapping or popping noise, this is normal) once you have loosened the panel, you will need to remove the plastic covering the access to the mirror (small triangle black plastic piece). this should now allow you to set the door panel aside, check to make sure you have removed all the clips. carefully remove the plastic lining cover the door, try not to tear or rip it. now you will need to remove the glass, there are two holes the allow access to the bolts for the window, connect your Power window switch and raise or lower till you can see them ( possibly a 10 mm socket) unscrew and set aside, hold the top of the window with one hand and lower the window to separate it form the brace. tilt the front side of the window down and remove glass set aside, replace your new window and re assemble as you have taken apart, most cases this is about two hours, Good Luck !!!

Jul 07, 2009 | 1997 Honda Civic

1 Answer

How to remove door panel for driver and passenger side doors


Hi. This Guide will help you with this issue.



Step1 Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver. Step2 Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights. Step3 Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out. Step4 Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side. Step5 Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off. Step6 Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lockmag-glass_10x10.gif are attached, then you just unclip the rod from the lock and remove them both together. Step7 Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle. Step8 Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.


Please rate and have a great day:)

Mar 25, 2009 | 2002 Kia Optima

1 Answer

Trying to remove driver side interior door panel on '88 Toyota PU


There is a cotter pin in the window crank, a pair of needle nosed pliers should be able to grab it

Dec 02, 2008 | 1988 Toyota Pickup

1 Answer

95 blazer, front driver window motor broken need to get window up


When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

Nov 30, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
1998 Mitsubishi Mirage Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...