Question about Lexus GS

Open Question

How to remove front bumper lexus 2007 GS 350

Wanting to remove front bumper to replace passenger side headlight ballast

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 17 Answers

SOURCE: Replace front side running light in a 2000 Lexus RX300

Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Posted on Aug 18, 2009

  • 60 Answers

SOURCE: I have to replace the ballast for the HID

You need to remove the front bumper. Five push clips along the hood line, remove the headlight wipers (if equipped), one T25 screw in the front of each fender well, then two 12mm bolts under the headlights (1 each side). Then there are 4 10mm bolts holding the headlight in.

Posted on Aug 27, 2009

  • 346 Answers

SOURCE: my 2005 lexus rx 330 (passenger side) has

Usually, the quickest/easiest solution is the replacement of the headlamp assembly. Your warranty provider may see it otherwise, but with an extended warranty, the seal failure should be covered.

You can try removing the bulb yourself and allowing the lamp to dry, then checking to see if the problem persists within a reasonable amount of time to ensure that it is in fact a bad seal, or you can submit warranty service to your provider.

Posted on Dec 26, 2009

emissionwiz
  • 75797 Answers

SOURCE: how to change lexus 2006

the ballast is part of the HID headlight assmbly, is that what u have? if so then here is how to replace the assembly or also just the ballast once the headlight is out.
1.Open the hood of your 2006 Lexus and locate the mounting screws on the top of the headlight assembly.

  • 2 Unscrew the mounting screws using a screwdriver.
  • 3 Slide the headlight assembly forward and unplug the power connector from the back of the Lexus' HID ballast on the back of the xenon headlight.
  • 4 Slide the headlight assembly out of the vehicle.
  • 5 Turn the headlight bulb counter-clockwise and pull it out of the headlight assembly to remove it.
  • 6 Install the headlight bulb into the new housing assembly. Installation is the reverse of removal. Make sure you align the tabs on the bulb with the notches in the back of the new assembly and turn the bulb clockwise to lock it into place.
  • 7 Reconnect the power connector and reinstall the headlight housing and secure it with the factory mounting screws.
  • Posted on Oct 29, 2010

    • 1 Answer

    SOURCE: 2005 Lexus RX330 HID ballast replacement,

    I have a 2005 Lexus Rx330 with HID AFS headlight. My passenger side light went out. I thought the bulb burnt out, so I bought a new bulb. After replacing the new bulb, it happened exactly like my old bulb. It light up lightly and then total black out. What's wrong with it? I thought the ballast burnt. I called Lexus dealer and asked for the new ballast/transformer. Surprised me, they don't know what is it. They told me they only know the wiring harness and the socket, but not the ballast ??????? Could you tell me what do I need to replace?

    Thanks,

    Posted on Apr 08, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Hi, I have a 2007 Lexus GS350 and after replacing the Xeon bulb the "Check Headlight" warning is still on, any idea how to reset? Thanks, Jeff


    HI,
    Looking online I'm not finding anything obvious.

    Is it a 'Lexus' bulb? A specific bulb may be required to properly 'connect' w/the car's computer system.

    Check your Owner's Manual and/or call the Dealer for more info.

    GL,
    TD

    Dec 14, 2016 | 2007 Lexus GS 350 AWD Sedan

    1 Answer

    How to take passenger headlamp out of 328i bmw 2008 so it can be replaced?


    2008 328i Passenger headlight assembly removal.

    The headlight assembly is held in by 4 "star" bolts (size 25); 2 visible on the top of the assembly, 2 not visible or easily accessible.

    The 2 bolts not so visible require that the front half of the wheel well come off and the front bumper or "nose" of the car.... The bumper is what needs to come off, but there are 2 bumper bolts hidden by the wheel well.

    The wheel well is held in by 7mm bolts, 2 of which are actually bolted to the bumper on the bottom.

    The front bumper is held on with 7mm bolts on the bottom edge, and star bolts, size 25, accessible on the top edge. (Hood open). Here were my steps.

    1. Jack up the car on the side you are replacing, remove wheel.
    2. Using 7mm socket, remove all the bolts to peel off the front half of the wheel well. With the wheel well out, you can see the 2 other star bolts holding the headlight assembly, but you can only remove one of them... even if you were good enough to get both removed, the headlight assemble will not push out through the bumper.... Keep going with bumper removal.
    3. Remove 2, 7mm bolts of the front bumper that are now visible up near the outer edge of the headlight assembly.
    4. At this point I removed the bumper's top edge start bolts and bottom edge 7mm bolts about 3/4 of the way across the bumper...
    5. The bumper is very flexible and you can now pull it back , reach in, and get that last difficult star bolt on the headlight assembly....
    6. Don't forget the one electrical connector....
    7. I also recommend testing the new assembly by plugging it in before removing anything

    Nov 09, 2012 | Cars & Trucks

    1 Answer

    2008 lexus gs 350 fuse box location


    On this website, you find fuse box diagram and description for Lexus GS350 (2007)

    Lexus GS350 2007 fuse box diagram Auto Genius

    Jun 19, 2012 | 2007 Lexus RX 350 FWD

    1 Answer

    No sound my car radio gs 350


    if the display lights are not working as well, then have your radio fuse replaced. it is located on the kick panel, under your steering wheel left side.

    May 17, 2012 | 2007 Lexus GS 350 AWD Sedan

    1 Answer

    Condensation build up , passanger side head light. Why? How to Fix??


    Have to replace the entire headlight assembly because it's filled with water due to bad drain or bad seal or it was in an accident of some sort.

    Aug 04, 2010 | 2007 Lexus GS 350 AWD Sedan

    2 Answers

    Need to change the passenger side headlight


    This video will show you how to change the headlight in your Accord.">

    May 19, 2010 | 1996 Honda Accord

    1 Answer

    2005 Lexus RX330 HID ballast replacement, passenger side headlight. What is the removal procedure please?


    I have a 2005 Lexus Rx330 with HID AFS headlight. My passenger side light went out. I thought the bulb burnt out, so I bought a new bulb. After replacing the new bulb, it happened exactly like my old bulb. It light up lightly and then total black out. What's wrong with it? I thought the ballast burnt. I called Lexus dealer and asked for the new ballast/transformer. Surprised me, they don't know what is it. They told me they only know the wiring harness and the socket, but not the ballast ??????? Could you tell me what do I need to replace?

    Thanks,

    Feb 02, 2010 | 2005 Lexus RX330

    1 Answer

    My 2005 lexus rx 330 (passenger side) has condensation. Is the best solution to replace the headlight unit? I also have a extended bumper to bumper warranty, will this be covered?


    Usually, the quickest/easiest solution is the replacement of the headlamp assembly. Your warranty provider may see it otherwise, but with an extended warranty, the seal failure should be covered.

    You can try removing the bulb yourself and allowing the lamp to dry, then checking to see if the problem persists within a reasonable amount of time to ensure that it is in fact a bad seal, or you can submit warranty service to your provider.

    Dec 26, 2009 | 2007 Lexus GS 350 AWD Sedan

    1 Answer

    I have to replace the ballast for the HID headlights on my 2004 XC70 volvo and it is under the headlight assembly. I just need assistance on how to remove the passenger side headlight assembly


    You need to remove the front bumper. Five push clips along the hood line, remove the headlight wipers (if equipped), one T25 screw in the front of each fender well, then two 12mm bolts under the headlights (1 each side). Then there are 4 10mm bolts holding the headlight in.

    Aug 13, 2009 | 2004 Volvo XC70

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    517 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lexus Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    ROBERT GARCIA
    ROBERT GARCIA

    Level 3 Expert

    881 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Are you a Lexus Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...