Question about Cars & Trucks

Open Question

Remove Center Floor Console from 96 Olds Achieva

Need to remove console to replace carpet

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

countrysi248
  • 443 Answers

SOURCE: 1991 camaro... How to remove center console

the best way to do it is take the center console out and the seats so you can properly weld in new floors .. unless your going to just put some tin over them if your going to do this you dont have to remove the console just the seats so you can get the carpet up to place the tin in place..

Posted on Apr 20, 2009

GM Elec
  • 1000 Answers

SOURCE: need instructions on how to remove center console to access electric window switch.

Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.

  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

Posted on May 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 buick lacrosse console gear indicator bulb


Transmission Floor Shift Control Indicator Lamp Replacement

Remove the front floor console. Refer to Front Floor Console Replacement.
Rotate the floor shift control indicator lamp socket (2). Pull the socket from the trim bezel.
Remove the bulb from the socket.

Front Floor Console Replacement

Preliminary Procedures
Remove the rear floor console. Refer to Rear Floor Console Replacement.
Remove the instrument panel lower trim plate. Refer to Instrument Panel Lower Trim Plate Replacement.
Set the parking brake, then shift the transmission into drive and push the shift indicator down until it locks, to allow clearance to remove the console.
1
Front Floor Console Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Front Floor Console Bolt (Qty: 2)
Tighten
10 N·m (88 lb in)
3
Front Floor Console Assembly
4
Front Floor Console Retainer Clip (Qty: 2)

Feb 24, 2017 | 2009 Buick LaCrosse

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

How do I remove the center console of a Isuzu Ascender


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

Feb 05, 2015 | 2006 Isuzu Ascender

1 Answer

Center console removal


Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.



showgif.do?image=1875475





tif.gif








Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure




  1. Disconnect the electrical connectors.


  2. When replacing the front floor console accessory housing assembly, transfer all necessary components





  1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .


  2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .



1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures


  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .



1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)





showgif.do?image=1858392





tif.gif








Callout







Component Name






Preliminary Procedures




  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .


  3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .







1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure



  1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.


  2. Disconnect the electrical connectors.


  3. With the aid of an assistant remove the console assembly from the vehicle.


  4. When replacing the front floor console, transfer all necessary components.





h4hqqpweof7+aaaaaelftksuqmcc

arzs+0tf0j6faaaaaelftksuqmcc

Jan 10, 2015 | 2008 Buick Enclave

1 Answer

How do I remove the center console to replace carpet


it has screws.
the FSm covers this, as does alldata.com
some cars the seats must come out.
most just screws.

Oct 12, 2014 | 1989 Toyota Camry

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

1991 camaro... How to remove center console


the best way to do it is take the center console out and the seats so you can properly weld in new floors .. unless your going to just put some tin over them if your going to do this you dont have to remove the console just the seats so you can get the carpet up to place the tin in place..

Apr 19, 2009 | 1991 Chevrolet Camaro

1 Answer

Radio Installation for a 96 Oldsmobile Achieva


I just replaced my radio on my 97 olds so im thinking it should be the same. You have to completely remove the lower dash. this involves popping many of those lock things but be careful cause they break easy. Also you will need to remove multiple screws from around the lower dash, then it will just drop down and you can remove the radio.

Oct 26, 2008 | 1997 Oldsmobile Achieva

1 Answer

Replacing a heater core in a 1994 olds. achieva.


  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Raise and safely support the front of the vehicle.
  4. If necessary, remove the rear lateral transaxle strut mount.
  5. Detach the drain tube, then disconnect the heater hoses from the core tubes.
  6. Carefully lower the vehicle.
  7. Remove the console if equipped.
  8. Unfasten and remove the sound insulators, console extensions and/or steering column filler, as required.
0900c152800a93fc.jpgFig. 1: Unfasten the sound insulator retaining bolts ... 0900c152800a93fd.jpgFig. 2: ... then remove the sound insulator
  1. On some models it may be necessary to remove the steering column opening filler.
  2. Remove the floor or console outlet ductwork and hoses.
  3. Remove the heater core access cover.
0900c152800a93fe.jpgFig. 3: Remove the heater core access cover
  1. Unfasten the heater core mounting clamps/bolts, then extract the heater core from the vehicle.
0900c152800a93ff.jpgFig. 4: Unfasten the heater core retaining bolts; most later models are secured with clamps 0900c152800a9400.jpgFig. 5: Remove the heater core from the vehicleTo install:
  1. Install the heater core, then secure using the clamps/bolts.
  2. Fasten the heater core cover.
  3. Connect the outlet hoses and ducts.
  4. Install the sound insulators, console extensions and/or steering column filler.
  5. Raise and safely support the vehicle.
  6. Install the drain tube and connect the heater hoses to the core tubes.
  7. If removed, install the rear lateral transaxle strut mount, if removed.
  8. Carefully lower the vehicle.
  9. Connect the negative battery cable.
  10. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Recheck for leaks and check coolant level. Add if necessary.6d0c523.jpg182943c.jpg164cdd5.jpg8032c04.jpg18be863.jpg

Oct 21, 2008 | 1994 Oldsmobile Achieva Special Edition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...