Question about 2005 Jeep Wrangler

1 Answer

I have a 2005 Jeep Wrangler X. When the power distribution center is connected there is a short to ground. Removing the battery connection to the power distribution center the short goes away. I have removed all fuses and circuit breakers in the power distribution unit and the short does not go away. I have removed all the fuses one by one in the fuse box in the glove box and the short remains.This has drained my battery down to 7.0 volts three times. I have charged the battery and had it checked at the local auto parts store and they said it is ok. If the vehicle is not started and driven every 3 days the battery drains to 7 volts. Charging system has been checked and is ok. ?????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Its bad,the PDC
no country stated, no engine stated,? why?
the 2005 (answering for USA)
PDC hard short all fuses, all breakers all relay out
means what?
well power distribution2 below shows all that, every wire there.
ASD relay pulled? you never said relays, they can (weld closed inside contacts can)) and is unfused, this relay. fact
i read the 22 pages for you there,
its just fuses and relays, no magic until 2007 (TIPM electronics)
this car is easy fix,. due to 2005 year.

looking now , TJ unlimited it is.
see the manual yet, see how this all works 2003 to 2006 year.
chapter 8w shows wiring, and modules the rules.

8w, pdc 2, chapter see that here, its there, clear as day.'



http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Posted on Mar 30, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mikey108
  • 475 Answers

SOURCE: 1989 Jeep Cherokee - Electrical Problem - horn, brake lights, blinkers, radio/cd...

There could be a fusible link under the hood off the starter relay that is burnt out.

Posted on Oct 13, 2008

sodeep
  • 3267 Answers

SOURCE: Battery won't stay charged while running. Alternator is fine tho.

It seems that your battery is not getting its charging amount from the rectifier which comes from the dynamo when the engine is in running condition. So just your rectifier and check the output of the dynamo to be sure thats OK............sodeep

Posted on May 21, 2009

  • 6982 Answers

SOURCE: I have a 1999 jeep cherokee 4x4 4.0L I6. I was

If you had a short that large before you started working on the batt cables, it would have burned long before it did. Check your work over and see where it's grounding. You can make a temporary link by using a new piece of wire the same as the gauge at both ends of the link and sectioning in a short piece of smaller ga. wire. Hopefully you didn't damage the alternator or other electronics. The original problem sounds like possibly the fuel pump anti drain-back valve is bad (integral with pump) Testing pressure will verify that.
You can disconnect alternator, but the fuse method you mentioned sounds more reasonable.

Posted on Jun 15, 2009

  • 1 Answer

SOURCE: i would like to disable the factory anti-theft and

Try Turn your vehicle on, while its on unhook the alarm box from behind the dash. if you attempt to do this without the vehicle on it will not work. an other solution would be to ground the purple and yellow wire on the drivers side door

Posted on Sep 05, 2009

  • 1 Answer

SOURCE: 2005 Jeep Grand Cherokee battery will drain

Ditto here on a 2005 jeep. We bought it new and found the battery dead on a few mornings the first year. Nothing left on. Did the new alternator thing about 2 yrs. ago and a few batteries along the way. This is what we noticed..... If you leave a CD in the CD player, that is the prime little devil that sucks out the juice. Now, we never turn off the car while a CD is in the dash. Now, maybe not necessary every time, but always overnight and now by habit, all the time, we make sure there is no CD inserted when the car is off. Hope this helps.

Posted on Dec 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 jeep wrangler wont start,has power to lights radio,battery good starer good.when you try to start inst.cluster does not come up.


check your engine block ground or the battery ground make sure the engine is properly grounded or is still grounded

Jun 19, 2012 | 2005 Jeep Wrangler

1 Answer

My jeep is failing to start. When jumped by another car, it still would not start. No lights come on in the dashboard, and the starter will not crank.


Remove, clean, and reinstall the cable connectors at the battery. Even if they LOOK clean, that may not be the case. Also, check the connections from the battery to the starter. Any of these connections being bad will cause a no power condition. There is also a power distribution center under the hood. It is a rectangular black box by the battery. There is a relay and maxi fuses for the engine power that comes straight from the battery. Check those maxi fuses.

Apr 14, 2011 | 1998 Jeep Wrangler

1 Answer

Had a dead short at pos. bat terminal.. it smoked thats how i found it... fixed it but now no spark and no fuel... what happened??? turns over.. lights are bright but nothin...HELP ME PLEASE


In the power distribution center, black fuse box under the hood next to the battery, there is an "engine" fuse. Controls power from the battery to the computer and engine electrical systems. A battery short would very possibly blow this maxi fuse (30 amp?).

Mar 05, 2011 | 1998 Jeep Wrangler

1 Answer

I have a 97 jeep wrangler, its a 2.5 liter 4cyl 5 speed. It has a starting issue now and again, it won't turn over lights and all electrical turns on but it just wont turn. When fuses are checked the start...


First thing you should do is check the starter draw. A simple way of doing that is to put a volt meter on the battery and crank the engine over. Volts should not drop below 9.5 while cranking.Since you replaced the starter, though some can be defective, the odds of getting a defective one with the identical problem you had before are slim. Therefore, it's more likely that you may have a bad ground. Check voltage between the positive terminal of the battery and the block (should read exact battery volts or just slightly less), then check draw again, with meter connected to battery and block. Readings should be identical to first draw test, or very close. Repeat, at the starter housing. If readings are low, clean the battery terminals and the engine end of the ground lead. Repeat testing and see if readings improve.
The reason you are doing this is that the starter draws more amps than any other item in the car. A bad ground can increase that draw above what the fuse can handle.
Biggest problem is that since it's intermittent, everything may look good when you test. "Blind" cure for that is to use a longer ground wire and attach the engine end to one of the starter bolts.
I also recommend that you check the starter relay (in the power distribution center) and any wiring associated with the ignition switch and that relay for grounding and good connections. Check under the dist center as well.

Jun 24, 2010 | 1997 Jeep Wrangler

2 Answers

My jeep starts fine when it is cold like first thing the morning but driving around town turning it on and off it will not start again until engine cools. I just replaced the crank shaft sensor. its a 95...


sometimes the ignition module will heat up under normal operation and fail to function until it cools off. you might take it off and take it to a parts store and they can test it for you. good luck.

May 28, 2010 | 1995 Jeep Wrangler

1 Answer

My ignition clicks but the car doesnt start


Could be dirty battery connections, bad ground, poor connection at the power distribution center, bad starter relay (in that box), bad starter solenoid (on starter) or the starter itself. If you have had overheating or other engine problems outside chance the engine could be seized (doubtful). Make sure you have 12 volts in the battery and that it can withstand a load test before going further than cleaning terminals or any testing will be invalid.

May 15, 2010 | 2005 Jeep Grand Cherokee

1 Answer

Is there a reset button for the fuel pump in a 2000 Jeep Wrangler?


There is no button for that...If the pump does not run check the relay in the power distribution center for power and ground, check the harness at the pump for power. If both are OK, likely the pump has gone bad.

Apr 28, 2010 | 2000 Jeep Wrangler

1 Answer

Is there a common place to check for a bad ground, or connection that would cause my 1989 4.2 liter wrangler to have symptoms of having a dead battery...when the battery is working perfectly. This happens...


Ground points vary from year to year but the main ones are from battery to block, strap from back of block to firewall, some small ones near the computer on the left fender and also one from battery to right fender.
You may have a starter solenoid that is worn out or a starter relay going bad. There is a ground wire going to that relay that can also give you a problem. To find it, you need to open up the power distribution center and check the ground at the relay itself, usually a double black wire (2) with a white stripe on them. Being that old, you may have replacement terminal ends as well. when cleaning them, you need to remove the wires from the attachment straps and clean there as well as the battery terminals.
Also, charge and have the battery load tested. Even a brand new one can sometimes have problems.

Apr 15, 2010 | 1989 Jeep Wrangler

1 Answer

Will not keep batery charged,i replaced alt,batery,belts are tight but gauge on dash reads in the red


There were a few different alternators used on those...I suggest you check the wiring to the unit and make sure you have power where it belongs. There may be a main fuse in the power distribution center near the battery...check that also.
Some have an external regulator. depending on the system, it is either a separate unit or is part of the computer. Be careful when testing that you don't arc to ground or it can cause more problems. make sure there is definite connection from the battery to the large wire on the alternator. Can't get more specific but something here should help.

Sep 26, 2009 | 1988 Jeep Wrangler

1 Answer

No power to ignition switch


There should be one large hot wire going to the ignition switch thaqt has power at all times...I would check that wire and trace it back to the battery. Quite possibly, it will connect to a fusable link coming from a main junction such as the alternator or the power distribution block. Either the link has failed or there is a bad connection there. I'm going to look through any diagrams I have and see if I can find anything else that may be helpful but that's a good start for now.

Jul 12, 2009 | 1990 Jeep Wrangler

Not finding what you are looking for?
2005 Jeep Wrangler Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...