Question about 1983 Oldsmobile Cutlass Supreme

Open Question

Need to change 1982 cutlass supreme ignition switch

How do you change a ignition switch in 1982 cutlass

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cooper0365
  • 347 Answers

SOURCE: i need to know how to change my ignition lock

ok first thing first take steering wheel off its kinda hard to do anyway take steering wheel off u might loosen the nut on the steering half way off and put your knees on back of steering wheel then hit nut with hammer as u pull up with your knees or buy a wheel puller cost around 20.00 but id rather just use hamer and my knees after u get wheel off they will be a lock wheel its black in the center is a meatal o ring clip u have to push down realy hard on that round lock and take o ring out after u get it out pull the black ring lock off then the plastic horn thing out then u will see the turn sng switch they are three screws in it taake them out dont take wires loose leave them just pull it out let it hang down thenu will look down see on back of lock mist have a screw there lossen it then take switch out slide the new one in then fun part putting all back together

Posted on Oct 17, 2009

  • 7353 Answers

SOURCE: a belt diagram for a 1982 cutlass supreme 3.8

Diagram? just v belts. It should have 4...... ALT PS A/C and Air Pump.

Posted on Dec 18, 2009

ftw1952
  • 10319 Answers

SOURCE: How do you change the

If the key lock switch is what you want I would get a locksmith to do it. The air bag coil and the bag are very touchy items to deal with to remove. ALSO many specialized tools are needed to remove the parts required to install the switch

Posted on Aug 01, 2010

postings909
  • 130 Answers

SOURCE: How do you change the

HUH WHAT YEAR???????? AND YES THEY DO OUT OFTEN. TO REPLACE ONE YOU NEED TO REMOVE THE STEERING WHEEL AND ASSEMBLY SNAP RING, TURN SIGNAL SWINCH ASSELY THAY HAS 3 SCREWS AND ONE SCREW THAT HOLD THE IGN SWITCH FROM THE INSIDE OF THE STEERING COLUM. ITS THE ONLY WAY. SEND ME A FEEBACK AND GOOD LUCK !!!!!!! IT TAKES A GOOD 2 HRS FOR THAT, METRIC SMALL SOCKET AND TORX SCREW DRIVER

Posted on Aug 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing ignition switch


remove steering wheel/switch must be in accessory with key in to remove and same with new switch in. mounting plate fastners inside cup under steering wheel.

Mar 20, 2014 | 1997 Oldsmobile Cutlass Supreme

1 Answer

I have a 1995 Olds Cutlass Supreme SL and when you turn the ignition off the care continues to run. Sometimes it will die within minutes and others it will sit and idle for a couple of hours. I have...


was the electrical ignition switch attached to the transmission changed? It is attached by the shift cable. If the contacts in that are worn or burnt it will continously run as you state

Jul 17, 2011 | 1995 Oldsmobile Cutlass Supreme

2 Answers

I have a 96 oldsmobile cutlass supreme sl wont start


it may need a new crank sensor the best thing for you to do is go to your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Dec 27, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

A belt diagram for a 1982 cutlass supreme 3.8


Diagram? just v belts. It should have 4...... ALT PS A/C and Air Pump.

Dec 18, 2009 | 1983 Oldsmobile Cutlass Supreme

1 Answer

I need to know how to change my ignition lock cylinder on a 1982 cutlass supreme


ok first thing first take steering wheel off its kinda hard to do anyway take steering wheel off u might loosen the nut on the steering half way off and put your knees on back of steering wheel then hit nut with hammer as u pull up with your knees or buy a wheel puller cost around 20.00 but id rather just use hamer and my knees after u get wheel off they will be a lock wheel its black in the center is a meatal o ring clip u have to push down realy hard on that round lock and take o ring out after u get it out pull the black ring lock off then the plastic horn thing out then u will see the turn sng switch they are three screws in it taake them out dont take wires loose leave them just pull it out let it hang down thenu will look down see on back of lock mist have a screw there lossen it then take switch out slide the new one in then fun part putting all back together

Oct 03, 2009 | 1983 Oldsmobile Cutlass Supreme

1 Answer

1994 cutlass supreme security light stays on and does not start


their is two wires they are white and go in to a orange sleve that sould be on the ignition switch, that is part of the security system in the car. It runs down inside the colunm and plugs in uder the dash. This is most likley your problem, the wires might have a short.

Jun 29, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...