Question about 2000 Chevrolet Silverado 1500

Open Question

2008 ford fusion rear brake drag

Rear brakes drag after replaced cuts pad life down a ton

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

  • 73 Answers

SOURCE: emergency brake foot pedal not working

Sounds like the cable is stuck also check the catch on the foot pedel

Posted on Mar 13, 2009

csmock132
  • 4669 Answers

SOURCE: 2002 tahoe breaks lock up during driving

It sounds like the rear calipers are bad. Raise the rear wheels and see if you can turn the tires. If you can't, open the bleeder. If you still can't replace the caliper. If you can turn the wheel after you open the bleeder, replace the brake hose to that wheel.

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: rear brake dragging

Suterman, RE: infamous GM right rear brake pad problem. A rapid inside RR brake pad wear problem is common on most GMC and Chevy trucks made from ?99 to ?04. The right rear brake caliper and pads are located in such a manner that road dirt/mud flies straight into them. This steady diet of grit causes the caliper to seize and the inside brake pad to wear out rapidly, causing the "squealing" or "grinding" noise often reported. SOLUTION: GM has had a problem with the rear brakes on their light duty trucks. There is a fix. The ALLDATA Information System shows GM Technical Service Bulletin # 00-05-23-005B, which they simply describe is a mud flap kit. This kit addresses the rapid brake pad wear problem. The GM mud flap kit is installed to block bombardment of road dirt and debris that is the cause of this very common problem. The GM kit part number is 15765007 and is pretty easy to install. I would suggest installing the mud flap kit before your next brake job.

Posted on Jun 05, 2009

  • 347 Answers

SOURCE: Rear brake pad dragging

ADJUST THE BRAKE CLEARANCE ON ALL FOUR WHEELS.

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace passenger side mirror on a 2014 ford fusion


Replace Your Car Passenger Side Mirror - How To - DIY ...

? 3:46
https://www.youtube.com/watch?v=77lBQ_CRqdo
Apr 10, 2012 - Uploaded by GregHint
See how even a novice can repair a passenger mirror on a FordEscape. ... Replace Your Car Passenger Side Mirror - How To - DIY .... Replace 2003-2008 Toyota Corolla Side Mirror, How to Change Install 2004 2005 2006
About 22,000 results (0.61 seconds) Search ResultsHow-To: Replace Ford Fusion side mirror (HD) - YouTube? 7:27https://www.youtube.com/watch?v=iGHeXUbvvJsMay 7, 2014 - Uploaded by Derrick HardingFord Fusion SEL 3.0 Liter V6 How to fix broken side mirrorIncludes: ... Published on May 7, 2014 ..... Great instructions - just replaced the driver's side mirror on my 2007 Fusion following your instructions. ... Front brake pad replacement 2006 - 2012 Ford Fusion Lincoln Mazda Pads Rotor Install Remove ...

Jan 08, 2016 | Ford Cars & Trucks

1 Answer

Rear brake cailpers won't collapse on 2007 ford fusion


Open bleeder valve & push caliper piston, in as
you rotate piston to screw in parking brake

Do this by hand,only use a clamp on the front calipers

Apr 08, 2013 | 2008 Ford Fusion

2 Answers

My brakes sound like they are grinding


check rear rotors and front rotors for rust buildup (flahlight helps). does the vehicle shake when you come to a hard stop? You will either need to have a front or rear or both brake job (rotors cut or replaced and new brake pads) If the vehicle is shaking when coming to a stop, its probably your front pads. If your hearing the noise from the rear its the rear pads or it you hear it from the front its the front pads. If there significant rust build up or your pads are low a brake job is recommended.

May 04, 2011 | 2008 Nissan Armada

1 Answer

I have a Ford Fusion 2008. In the last little whileWhen I brake I hear a heavy grinding sound. I don't hear it unless I turn the radio off and the heat down. It almost sounds like it's lagging. What would...


sounds like your brake pads are worn out depending ondamage to the brake rotors will depend on the cost. if you are lucky you will have to only replace the pads. if the discs are gouged out then you will have to either machine them flat again or buy new rotors also.

Jan 18, 2011 | 2008 Ford Fusion

1 Answer

I've removed the rear brake pads and am unable to get the brake piston to retract on my 2008 Ford Fusion


easy either buy the special tool or wind them in with a pair of water pump pliers and a G clamp ,having assistant helps if they apply light pressure to G clamp whilst you wind piston in ,clockwise

Oct 24, 2010 | Ford Fusion Cars & Trucks

1 Answer

How do I install rear brake pads on a 2008 ford fusion once calipers are removed?


unplug the brake fluid line from the caliper than squeeze the cylinders open then insert your new brakes into the clips then add more fluid and bleed the lines connecting them back to the brake caliper

Mar 10, 2010 | 2008 Ford Fusion

2 Answers

How do you press the brake caliper piston back on 2008


First, take a look at the piston, if it's flat or cup shaped, put an old pad at the piston and use channel locks to squeeze it back in, opening the tool wide to get it to catch the back of the caliper.
If....the piston has what looks like an "X" or cut outs, this is for a tool that spins the piston in with a special tool. (Subaru's and some other cars use this)
After you are all done and pump up the brakes, re-check the brake fluid level.

Dec 06, 2009 | 2008 Ford Fusion

1 Answer

Replacing brake pads on 2006 ford fusion


IF POSSIBLE GET A HAYNES MANUAL OR USE ONE WHEEL AS
A REFERENCE WHILE WORKING ON THE OTHER. BETTER GET
THE BOOK ESPECIALLY IF YOU HAVE REAR DISC CALIPERS.

Jul 19, 2009 | 2008 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...