Question about Cars & Trucks

Open Question

How do i change low beam headlight bulb on 20004 corolla

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: Changing the headlights

This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps

Posted on May 31, 2009

greg_margo
  • 1959 Answers

SOURCE: I need to change the low beam headlight bulb

  1. Remove headlight mounting bolts and nut
  2. Remove assembly
  3. Install headlight assembly (with new bulb)
  4. Replace/tighten headlight mounting bolts and nut
e2ac826.gif


Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High Beams Great. Low Beams very dim. All new ultra bright bulbs and new headlight assemblies. What can I do to have safe low beams?


You need to check voltages at the headlight connection and see what they are. If they are low then check the wires for bad ground connections, check the relay

Dec 01, 2015 | 1995 Toyota Corolla

1 Answer

I have a 1999 Corolla, and both headlights suddenly stopped working. The low beams don't work, but the high beams do. The fuses are fine.


low beam is a bulb on its own,usually under the big main bulb.the main big bulb works your normal night time driving and your high beam,ie.flashers.if 1 low beam has blown its more than likley a power serge blown the other side as they run off the same wiring.hope this helps.

Nov 02, 2013 | 1999 Toyota Corolla

1 Answer

Left Low Beam Headlight won't come on!


Check for power and a good ground at the bulb socket and if they are good then i would try another bulb.

Oct 30, 2012 | 2004 Toyota Corolla

1 Answer

My 1992 Corolla DX headlights won't come on! I have changed the fuses and the bulbs. The relay clicks when turning the switch and the wiring seems to be in good condition but I am no electrician. The...


Power flows from the battery to the main fuse. Then it flows to the control coil and contact side of the headlight relay. When you turn on the headlights, the headlight switch provides ground to the control coil in the headlight relay and that operates the contacts. The contacts allow power to flow to the right and left hand headlight fuses. Power flows to the headlights. The headlight switch is what provides ground to the high and low beams on the headlights.

To diagnose, remove the headlight relay. Using a voltmeter, check for battery voltage on terminals 3 & 4 in the socket with the key in the RUN position. Then turn on the low beams. Test for good ground on terminal 1 in the socket. If you're not getting ground, then you've got a problem with either a bad headlight combo switch or a bad ground. If you get good ground on terminal 1, reinstall the relay, turn on the low beams and test for power in the headlight sockets. If you get battery voltage, that confirms you've got good fuses and wiring up to that point. Next, check for good low beam ground on the red/green wire in the bulb socket. If you're not getting good ground, it's either a bad combo switch or bad ground from the combo switch. Then turn on the high beams and check for good ground on the red/yellow wire in the bulb sockets.

It wouldn't hurt to clean the ID ground on the left side of the instrument panel, but based on everything you've said so far, this sounds like a bad combo switch

Jul 26, 2017 | 1992 Toyota Corolla

2 Answers

Hi, could you please advice me how i can adjust the headlights for 92' toyota corolla? Thank you


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 10, 2009 | 1992 Toyota Corolla

1 Answer

Headlight problem


need to change the turn signal the power for the headlight lows is going thought that switch

Jan 19, 2009 | 1998 Toyota Corolla

1 Answer

Changing the headlights


This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps

Dec 20, 2008 | 2004 Hyundai Tiburon

1 Answer

1992 toyota corolla


Sorry, was not available at your time. Since the blue light comes on, this tells me that the hi-beam fuse is good. Go to the pass side headlamp, and, behind it, remove the connector for the inop bulb, and remove the bulb. Examine the filament on the bulb. Is it broken in half? If so, you need two hi-beam bulbs. Get back to me if you need more info.

Oct 15, 2008 | 1992 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...